Panasonic CZ-RTC4, Service Manual

Page: 55 / 68

Optional Controller
Manual of Controller
2 - 37
2. Wireless Remote Controller
( CZ-RWSU2N, CZ-RWSD2, CZ-RWST3N, CZ-RWSL2N )
12. Emergency Operation
21
(EN)
ENGLISH
Use [Emergency Operation]
in the following situations when there is an urgent need.
•
When the remote controller
’s batteries have failed.
•
When the remote controller is broken.
•
When the remote controller is lost.
*
1
Figures: CZ-R
WSU2N, CZ-R
WSD2, and CZ-R
WST3N are of receivers
(inside indoor unit), CZ-R
WSL2N is of the operation panel (inside indoor
unit) and indoor unit (CZ-R
WSK2) is of its front panel.
CZ-R
WSU2N/CZ-R
WSD2/Indoor Unit (CZ-R
WSK2)/CZ-R
WST3N
CZ-R
WSL2/CZ-R
WSC3
Start: press [Emergency Operation]
of the receiver
.
If the indoor temperature is 24 °C or greater when the unit sta
rts running, it
will act as a cooler
.
If the indoor temperature is less than 24 °C when the unit star
ts running, it
will act as a heater
.
Stop: press [Emergency Operation]
of the receiver again.
CZ-R
WSD2
Start/Stop
Start/Stop
C
Z-
R
W
SU
2N
CZ-R
WST3N
Start/Stop
Start/Stop
Start/Stop
Start/Stop
Start/Stop
TIMER
OPERA
TION
ST
ANDBY
CZ-R
WSL2N
CZ-R
WSC3
00̲OI̲303000.indb 21
2015/02/20 16:23:08
20
(EN)
Wireless remote controller address display
•••••
Address switch position
Address
Address
Address
Address
Address
Address
Address
ALL
1234
5
6
Receiving is possible at all address positions
䠍
䠎
䠏
䠐
㻻㻲㻲
㻻㻺
䠍
䠎
䠏
䠐
㻻㻲㻲
㻻㻺
䠍
䠎
䠏
䠐
㻻㻲㻲
㻻㻺
䠍
䠎
䠏
䠐
㻻㻲㻲
㻻㻺
䠍
䠎
䠏
䠐
㻻㻲㻲
㻻㻺
䠍
䠎
䠏
䠐
㻻㻲㻲
㻻㻺
Setting Addresses
(CZ-R
WSK2)
(Setting the address of the indoor unit)
1.
Set the address for the remote controller following the procedure under the section “Setting Remote Controller Addresses” (see page 19).
2.
Press [Emergency Operation]
of the indoor unit for four
seconds or longer
.
When you do this, the lamps of the display will blink one after another
.
3. Press
on the remote controller
.
4.
The buzzer will sound and the address of the indoor unit will change to the address displayed on the remote controller
.
5.
If you press [Emergency Operation]
of the indoor unit once,
the lamps on the indoor unit’
s display will turn off.
Notes
•
Please
do
not
hold
the
[Emergency
Operation]
button of the indoor unit down
while the indoor unit’
s display lamps are blinking one after another
.
•
Make sure to operate while the indoor unit is stopped.
•
The address of indoor unit is set to "ALL" at the time of the
shipment.
11. Addresses
(Cont.)
ON
OFF Interruptor ON/OFF
00̲OI̲303000.indb 20
2015/02/20 16:23:07
SM830241-00_2WAY SYS.indb 37 2015/03/26 14:55:13