Panasonic CZ-RTC4, Service Manual

Page: 54 / 68

Optional Controller
Manual of Controller
2 - 36
2. Wireless Remote Controller
( CZ-RWSU2N, CZ-RWSD2, CZ-RWST3N, CZ-RWSL2N )
11. Addresses
19
(EN)
ENGLISH
In both multi and single unit installations,
when more than one indoor units
are installed in the same room with a compatible wireless remote controller
,
addresses can be set up to avoid crosstalk. By setting the address switches on the receivers and matching them with the number of addresses on the remote controller
, up to six indoor units can be
controlled separately with the remote controller
. (When using units in a

exible
combination or operating multiple units simultaneously
, they cannot be
controlled individually as they are operated at the same time.) There are separate address settings: receiver addresses for the receivers
*
1
,
and transmitter addresses for the remote controller
.
For more information, please contact the distributor where the product was purchased. •
The setting procedure is dif
ferent for indoor unit (CZ-R
WSK2). (See page 20.)
•
These settings are saved in nonvolatile memory in the remote co
ntroller
, so
even when its batteries are changed, the settings do not have to be made again.
*
1
CZ-R
WSD2N/CZ-R
WST3N is of receivers (inside the indoor unit); CZ-
R
WSL2N is of an operation panel (inside the indoor unit).
Checking Addresses
When you press
on the remote controller
, its current address appears on
the display
. If this address corresponds to the address of a receiver
*
2
, the
buzzer sounds. (If it is on
ALL, the buzzer will always sound.)
If it is on
ALL, it can be operated regardless of receiver addresses. Point
the
remote controller at the receiver you wish to operate and transmit. *
2
CZ-R
WSL2N is an operation panel (indoor unit).
Matching
Up Addresses
Setting Remote Controller
Addresses
1.
If you press
and
at the same time,
will blink.
2. While
holding
down, every time you press
, it cycles
from ALL

1

2

3…6

ALL.
Set it to the receiver address switch of the indoor unit you wi
sh to operate.
3.
When you release
, the address that was displayed is set.
When you do this, if it corresponds to the receiver
’s address setting, the
buzzer sounds.
00̲OI̲303000.indb 19
2015/02/20 16:23:06
9. Using the Remote Controller
18
(EN)
•
Point the transmitter of the remote controller at the receiver
. When the
signal is received properly
, it will beep one time. (It only beeps two times
when the unit starts operating.)
•
The signal can be received at a distance of up to about 6 meter
s.
This
distance should be used only as a guide. It depends on battery
strength.
•
Make sure nothing is between the remote controller and the rece
iver that
could block the signal.
•
Do not leave the remote controller in direct sunlight, where th
e wind from
the air conditioner can blow directly on it, or near any other
heat source.
•
Take care not to drop, throw
, or wash the remote controller with water
.
•
The signal from the remote controller may not be received in ro
oms with
rapid start

uorescent lighting, inverter lights, plasma displays, LCD
televisions (monitor), etc. For more information, please conta
ct the
distributor where the product was purchased.
W
all Mount Use
•
Press
from the location
you wish to mount the remote controller and make sure the signal is received properly
.
•
Pull the remote controller forward to remove it.
10. For Best Results
Don’t get the remote controller too far away from the receiver
.
This may cause a malfunction. Be sure to keep the remote controller in the same room as the r
eceiver
.
Point the remote controller at the receiver
.
When the signal is received properly
, it will beep one time.
Avoid locating the remote controller where it is covered, such as behind a curtain.
Keep it out in the open.
Remote control holder
1
2
Fasten the remote control holder with screws.
Fitting the remote controller in the holder
Push Fit in
00̲OI̲303000.indb 18
2015/02/20 16:23:06
SM830241-00_2WAY SYS.indb 36 2015/03/26 14:55:12