manualshive.com logo in svg

Panasonic CU-B14DBE5, Service Manual, Page: 8 / 109

Share
Download
Panasonic CU-B14DBE5 Service Manual Download Page 8

8

2.5.

Group Control Equipment

 

 

 

Wired

remote

control

Group control by one remote control

• All air conditioner units are con-

trolled as a whole by remote control.

• All indoor units operate in the same

mode.

[Remote side]

• Optional wired remote con-

trol  CZ-RD513C

[Local side]

Not needed

Twin remote control separate control

• Each indoor unit can be operated by

either one of the two remote control.

• Apart from timer setting time, dis-

plays for two remote control are 
identical.

• Last button pressed has priority

(main or slave is set at remote con-
trol unit).

[Remote side]

• Optional wired remote con-

trol 

[Local side]

• Optional wired remote con-

trol CZ-RD513C

 

Common

control

Common control / group

• Operation is possible using either

wired or wireless remote control 
unit.

• Last button pressed has priority.

• Optional wired remote con-

trol and wireless remote 
control

Wired CZ-RD513C
Wireless CZ-RL513T

Summary of Contents for CU-B14DBE5














































































































Reviews:

No comments