background image

English

11

How to use

To adjust airflow direction

(Remote control display)

• Keeps the room ventilated.
• If AUTO air swing is set, the flaps swings 
  left/right and up/down automatically.
• The horizontal and vertical flap are fixed at the
  predetermined position.
• Do not adjust the flap by hand.

(Vertical)

(Horizontal)

To set the timer

To turn ON and OFF the unit at a preset times. 

Auto Restart Control

• If power is resumed after a power failure, the 

operation will restart automatically after a period 
of time with previous operation mode and airflow 
direction.

• This control is not applicable when SLEEP, CLEAN,
  TIMER is set.
• In TIMER set conditions if there is power reset then
  unit will start in stand by mode.

To select fan speed 

(Remote control display)

(Low)

(Medium)

(High)

AUTO

FAN

QUIET

• For AUTO, the indoor fan speed is automatically
  adjusted according to the operation mode. 

Operation conditions

Use this air conditioner under the following
temperature range.
DBT  : Dry bulb temperature
WBT : Wet bulb temperature

52

30

• Can be activated even when the unit is turned
  off. In this condition, the unit will operate as a fan
  with AUTO fan speed and louver swing.

nanoe-G Purifier

nanoe-G

For faster cooling and a longer 
air throw 

JETSTREAM: Display on remote LCD

• This operation stops automatically after 1 hours.

JET

STREAM

QUIET: To enjoy quiet operation

• This operation reduces airflow noise.

ON

OFF

CANCEL

1

2

• To cancel ON or OFF timer, press        . 
• If timer is cancelled manually or due to power 

failure, you can restore the timer again by 
pressing         or        then wait for “5” sec. 

• The nearest timer setting will be displayed and 

will activate in sequence.

• When ON Timer is set, the unit may start 

earlier (up to “15” minutes) before the actual 
set time in order to achieve the desired 
temperature on time.

ON

OFF

CANCEL

Select ON or OFF
timer

Set the time

Confirm

Example:
OFF at 14:00  

Press the OFF 
button.  

OFF

OFF

OFF

OFF

OFF

OFF

Wait for “5” second to set timer.  

Press OFF button again to
increase timer time in step
of “10” minutes.  

C

M

Y

CM

MY

CY

CMY

K

ACXF55-2705̲OL.ai   11   3/3/2020   9:56:31 AM

ACXF55-2705̲OL.ai   11   3/3/2020   9:56:31 AM

Summary of Contents for CS-WU12WKY Series

















Reviews: