manualshive.com logo in svg

Panasonic CS-QE12MKE, Service Manual, Page: 28 / 97

Share
Download
Panasonic CS-QE12MKE Service Manual Download Page 28

28 

 

 

 

 

 

 

 

11.2.4  Connect the Cable to the Indoor Unit  

1  The inside and outside connection cable can 

be connected without removing the front grille. 

2 

Connection cable

 between indoor unit and 

outdoor unit shall be approved 
polychloroprene sheathed 4 x 1.5 mm

2

 flexible 

cord, type designation 245 IEC 57 or heavier 
cord. 

3  Bind all the indoor and outdoor connection 

cable with tape and route the connection 
cable via the escapement. 

4  Remove the tapes and connect the 

connection cable between indoor unit and 
outdoor unit according to the diagram below. 

 

 

 

 

 

 
 
 
 
 
 

5  Secure the connection cable onto the control board with the holder (clamper). 

o

 

Ensure the colour of wires of outdoor unit and the terminal Nos. are the same to the indoor’s 
respectively. 

o

 

Earth wire shall be Yellow/Green (Y/G) in colour and longer than other AC wires for safety reason.

Summary of Contents for CS-QE12MKE


































































































Reviews:

No comments