manualshive.com logo in svg

Panasonic CS-PC12MKF, Service Manual

Share
Download
Panasonic CS-PC12MKF Service Manual Download Page 47

47

• AUTO COMFORT Stop condition.

- Press AUTO COMFORT button again.
- OFF Timer activates.
- Press OFF/ON button to turn off the air conditioner.
- Press AUTO OFF/ON button to turn off the air conditioner.

• ECONAVI & AUTO COMFORT operation could ON when any of the following conditions is fulfilled:

- During forced cooling or forced heating operation.
- During e-ion or individual patrol operation.

• Power Failure

- ECONAVI & AUTO COMFORT operation will be resuming after recovered from power failure.

• Timer Operation

- When unit is turn on by ON Timer and ECONAVI & AUTO COMFORT operation is ON during previous

operation before OFF, ECONAVI & AUTO COMFORT operation will not be ON automatically.

- When unit is turn on by ON Timer and ECONAVI & AUTO COMFORT operation is OFF during previous

operation before OFF, ECONAVI & AUTO COMFORT operation will not be ON automatically.

• Other Information

- ECONAVI & AUTO COMFORT, Powerful and Quiet cannot be operated at the same time.
- ECONAVI & AUTO COMFORT sensor initialized time is 70 seconds from power supplied to ECONAVI & AUTO COMFORT

sensor, or 70 seconds from the operation start.

* For first 15 minutes or until set temperature is reached.

Summary of Contents for CS-PC12MKF
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands