manualshive.com logo in svg

Panasonic CS-PC12MKF, Service Manual

Share
Download
Panasonic CS-PC12MKF Service Manual Download Page 44

44

12.9. Random Auto Restart Control

• If there is a power failure during operation, the air conditioner will automatically restart after 3 to 4 minutes when the power is

resumed.

• It will start with previous operation mode and airflow direction.
• If there are more than one air conditioner unit in operation and power failure occur, restart time for each unit to operate will be

decided randomly using 4 parameters:- intake air temperature, setting temperature, fan speed and air swing louver position.

• This Random Auto Restart Control is not available when Timer is set.
• This control can be omitted by open the circuit of JX02 (refer to printed circuit board indoor unit).

12.10. Remote Control Signal Receiving Sound

• Short beep sound will be heard when turn ON the air conditioner or enabling other operations.
• Long beep sound will be heard when turn OFF the air conditioner or disabling other operations.

Summary of Contents for CS-PC12MKF
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands