manualshive.com logo in svg

Panasonic CS-A18DKD, Service Manual, Page: 4 / 86

Share
Download
Panasonic CS-A18DKD Service Manual Download Page 4

2.2. Indoor Unit

Ionizer Operation

• Generate and discharge negative ion.

Random Auto Restart Control

• Unit will be restarted, when resume from

power failure, at previous setting.

Anti-Freezing Control

• To prevent indoor heat exchanger from

freezing.

Indoor Fan Speed Control

• Manual control fan speed

(High, Medium and Low).

• Automatic fan speed

•

•

Vertical airflow control can be adjusted
automatically or manually by remote control.
Horizontal airflow control can be adjusted
automatically or manually by remote control.

Airflow Direction Control

Automatic Operation Button

• Press for < 5 second to operate Automatic

operation mode.Use when the remote
control cannot be used.

• Press for > 5 second to operate Cooling

operation mode and compressor force
to on (“beep” sound will be heard). Used 
when test running or servicing.

• Within 20 second of Cooling operation, 

press continuously for > 5 second to enter 
various setting mode. “beep, beep” sound 
will be heard. (Used to toggle remote 
control signal receiving sound or select 
remote control transmission code.) 

AUTO

OFF / ON

Operation Indication Lamps (LED)

•

POWER

 (Green) ........ Lights up in operation,

blinks in Automatic
Operation judging.

•

QUIET

 (Orange) ........ Lights up in Quiet

Operation.

•

TIMER

 (Orange) ....... Lights up in Timer

Setting.

•

POWERFUL

 (Orange) .. Lights up in Powerful

Operation.

•

ION

 (Green) ........... Lights up in Ionizer

Operation.

•

SUPER 

ALLERU-BUSTER

 (Blue) ... Lights up in operation.

Operation Mode

• Heating, Cooling, Soft Dry and Automatic 

Operation.

Powerful Operation

• Reaches the desired room temperature 

quickly.

Timer Operation

• Delay OFF/ON Timer control.

Time Delay Safety Control

• Restarting is inhibited for approximately

3 minutes.

Quiet Operation

• To provide quiet operation.

7 Minutes Time Save Control

• To reduce the built up humidity inside

the room.

Anti-Dew Formation Control

• Anti-Dew Formation Control for indoor

unit discharge area.

Hot-Start Control

• To prevent cold air being discharge during

Heating operation starts.

Anti Cold Draft Control

• To prevent the cold draft during Heating

mode operation in thermo off condition.

4

CS-A18DKD CU-A18DKD / CS-A24DKD CU-A24DKD

Summary of Contents for CS-A18DKD























































































Reviews:

No comments