Panasonic CS-A18DKD Service Manual Download Page 3

Page: 3 / 86

2 Functions

2.1. Remote Control

Operation Start/Stop

OFF / ON

Room Temperature Setting

TEMP.

Operation Mode Selection

•

AUTO

Automatic Operation

•

COOL

Cooling Operation

•

HEAT

Heating Operation Mode

•

DRY

Soft Dry Operation

MODE

Time / Timer Setting

• Hours and minutes setting.

Clock Setting

• Current time setting.

Ionizer Operation Start/Stop

Indoor Fan Speed Selection

FAN SPEED

•

FAN

Low Fan Speed

•

FAN

Medium Fan Speed

•

FAN

High Fan Speed

•

AUTO

Automatic Fan Speed

FAN

Airflow Direction Control

• 24-hour, OFF / ON Real Timer Setting.

ON-TIMER

OFF-TIMER

Timer Operation Selection

SET

CANCEL

Timer Operation Set / Cancel

• ON Timer and OFF Timer setting and

cancellation.

CLOCK

AIR SWING

•

Vertical Automatic Airflow
Direction Control and Manual
Airflow Direction Control
(5 stages of adjustment).

•

Horizontal Automatic Airflow
Direction Control and Manual
Airflow Direction Control
(5 stages of adjustment).

Powerful Operation Start/Stop

POWERFUL

Quiet Operation Start/Stop

QUIET

Cooling, Soft Dry Operation.
• Increase or decrease set temperature

(16

C to 30

Automatic Operation
•

Operation with 2

C higher than

standard temperature.

•

Operation with standard temperature.

•

Operation with 2

C lower than

standard temperature.

CS-A18DKD CU-A18DKD / CS-A24DKD CU-A24DKD

Summary of Contents for CS-A18DKD























































































Search results

Summary of Contents for CS-A18DKD

Reviews:

Panasonic CS-A18DKD, Service Manual, Page: 3 / 86

Search results

Summary of Contents for CS-A18DKD

Reviews: