manualshive.com logo in svg

Panasonic CS-A18DKD, Service Manual, Page: 21 / 86

Share
Download
Panasonic CS-A18DKD Service Manual Download Page 21

8.5.7. Anti-Dew Formation Control

 • 

Purpose is to prevent dew formation on indoor unit air discharge area.

 • 

When room temperature is constant (±1°C) the following conditions occur for 30 minutes continuously, anti-dew formation will
activate:

 − 

Remote Control setting temperature is less than 25°C.

 − 

Compressor is on.

 − 

Cooling operation mode.

 − 

Indoor Fan motor operate at Low fan speed or QLo.

 • 

This control is cancelled immediately when above condition is changed.

 • 

Anti-Dew formation is control by:
 1. Increasing Air Flow Volume

 a. Lo fan speed

Lo fan speed is changed to Lo+ after 30 min to prevent dew formation.

 b. QLo fan speed

Dew formation may occurs at QLo cool, therefore QLo cool is operated only 1 hr 30 min (1 hr QLo, 30 min QLo +100
rpm). After that, it operates at QLo +180rpm (However Quiet LED remains on).

 2. Norrowing

Vertical Airflow Direction

 − 

During Anti-dew condensation prevention, Airflow Direction Auto-control angle change from 10° - 38° to 10° - 27° under
Cooling and Soft Dry operation mode.

21

CS-A18DKD CU-A18DKD / CS-A24DKD CU-A24DKD

Summary of Contents for CS-A18DKD























































































Reviews:

No comments