Panasonic CF-07 Series Service Manual Download Page 45

Page: 45 / 117

4. Removing the Main Board

1. Remove the main board block from the bottom cabinet.

2. Remove the Lithium Battery from the Battery Holder.

4.1. Removing the Wireless LAN Board

1. Remove the 2 screws and release the wireless LAN board

block.

Screw

<A>:XYN2+J6FZ

2. Remove the 4 screws and release the wireless LAN board.

Screw

<A>:XYN2+J5FN

4.2. Removing the Upper Main Board

1. Remove the 3 screws.

Screw

<A>:DFHE5025YA

Removing the PC Card Ejector and the Power Button
Guide.

1. Remove the 3 screws <A>.

2. Remove the single hexagonal screw <B>.

3. Remove the power botton from the upper main board.

Screw

<A>:XYN2+J4FZ

<B>:OXHM0034ZA

4.3. Removing the Serial Port Block

1. Remove the 2 screws.

2. Disconnect the connector.

Screw

<A>:XYN2+J6FZ

Block

18-2

Summary of Contents for CF-07 Series






















































































































Search results

Summary of Contents for CF-07 Series

Reviews:

Related manuals for CF-07 Series

Brands by name

Popular brands

Panasonic CF-07 Series, Service Manual

Search results

Summary of Contents for CF-07 Series

Reviews:

Related manuals for CF-07 Series

Brands by name

Popular brands