Panasonic CF-07 Series Service Manual Download Page 44

Page: 44 / 117

<A torque for tightening screws>

Please refer to the torque described on Exploded View.

1. Removing the Battery Packs

1. Slide the battery cover lock knob back and open the battery

cover.

2. Remove the 2 battery packs.

2. Removing the Top Cabinet

1. Remove the screw covers.

2. Remove the 6 screws<A>.

Screw

<A>:DXSB2+10FZL

3. Remove the top cabinet from the bottom cabinet.

4. Open the connector latch on the mainboard and remove the

flexible cable.

5. Remove the 2 screws.

6. Disconnect the antenna cable from the LED board.

Screw

<A>:XYN2+J5FN

3. Removing the HDD Block

1. Open the connector latch and remove the flexible cable.

2. Remove the 2 screws and release the HDD cover.

3. Remove the HDD from the HDD protection case.

4. Remove the HDD flexible cable.

Screw

<A>XYN2+C3

15 Disassembly/Reassembly

18-1

Summary of Contents for CF-07 Series






















































































































Search results

Summary of Contents for CF-07 Series

Reviews:

Related manuals for CF-07 Series

Brands by name

Popular brands

Panasonic CF-07 Series, Service Manual

Search results

Summary of Contents for CF-07 Series

Reviews:

Related manuals for CF-07 Series

Brands by name

Popular brands