Panasonic CF-07 Series Service Manual Download Page 33

Page: 33 / 117

5. HDD DIAGNOSIS

Make sure that connecting cables, connectors and AC adapter are not loose or disconnected prior to testing.

No.

Symptom

Troubleshooting

procedures

Source of

problem

No.

Result

1-1

Has the HDD been partitioned?

Does not boot from HDD.

Component

Go to No. 1-2
Improper setting

YES

2-1

Has the HDD been formatted?

Cannot read from HDD.
Cannot write to HDD.

Go to No. 2-2
HDD format

YES

3-1

3-2

Replace the HDD.
Does operation return to
normal?
Replace the HDD cable.
Does operation return to
normal?

Replace the HDD.
Does operation return to
normal?
Replace the LED PCB.
Does operation return to
normal?
Replace the Main PCB.
Does operation return to
normal?

Damage to data written to
HDD.
Damage to data read from
HDD.
HDD contents are
destroyed.

HDD

Go to No. 3-2

YES

5-1

5-2

5-3

5-4

Has the HDD been
configured in the OS?

Access lamp does not
light.

Go to No. 5-2

Improper setting

YES

4-1

Replace the HDD.
Does operation return to
normal?

Dignositic Test reports
problem in HDC or HDD.

6-1

Replace the HDD.

Abnormal sound.

HDD

2-2

2-3

Replace the HDD.
Does operation return to
normal?
Replace the HDD cable.
Does operation return to
normal?

HDD

Go to No. 2-3

YES

1-2

Are there system files on the
HDD?

Go to No. 1-3
Software on the
HDD

YES

1-3

1-4

Replace the HDD.
Does operation return to
normal?
Replace the HDD cable.
Does operation return to
normal?

HDD

HDD cable

Go to No. 1-4

Main PCB

IC11

YES

HDD cable

Main PCB

IC11

YES

HDD cable

Main PCB

IC11

YES

HDD

Main PCB

IC11

YES

HDD

Go to No. 5-3

YES

LED PCB

Go to No. 5-4

LD2

YES

Main PCB

HDD cable

IC11

YES

Hard disk failure

Does executing FDISK
correct the problem?

7-1

HDD cable

YES

Main PCB

IC11

Go to No. 7-2

Format data
destroyed

YES

Replace the HDD.
Does operation return to
normal?

7-2

Go to No. 7-3

HDD

YES

Replace the HDD cable.
Does opration return to
normal?

7-3

14-6

Summary of Contents for CF-07 Series






















































































































Search results

Summary of Contents for CF-07 Series

Reviews:

Related manuals for CF-07 Series

Brands by name

Popular brands

Panasonic CF-07 Series, Service Manual

Search results

Summary of Contents for CF-07 Series

Reviews:

Related manuals for CF-07 Series

Brands by name

Popular brands