72
Web screen configurations
(continued)
Transmission type
Select the transmission format for H.264 images.
Setting value:
Unicast port
(AUTO)
Up to 14 users can access a single camera at
the same time.
[Unicast port (Image)] and [Unicast port
(Audio)] will be configured automatically when
images and audio are sent from the camera.
We recommend selecting the [Unicast port
(MANUAL)] setting when the port number
transmitting the H.264 images does not need to
be fixed (e.g., during use within a network).
Unicast port
(MANUAL)
Up to 14 users can access a single camera at
the same time.
[Unicast port (Image)] and [Unicast port (Audio)]
must be configured manually when images and
audio are sent from the camera.
When transmitting H.264 images via the
Internet, configure a fixed transmission port for
the broadband router (hereafter referred to as
“router”) (page 90). For details, refer to the
operating instructions for the router.
Multicast
An unlimited number of users can access a
single camera at the same time.
When transmitting H.264 images via multicast,
enter the [Multicast address], [Multicast port],
and [Multicast TTL/HOPLimit].
Factory settings:
Unicast port (AUTO)
●
For details on the maximum number for
simultaneous access, see page 56.
Note
Unicast port (Image)
Enter the unicast port number (used when sending
images from the unit).
Usable port number range:
1024 to 50000
●
Only even numbers can be specified.
●
The port number cannot be set to 10670.
Factory settings:
H.264(1): 32004
H.264(2): 32014
H.264(3): 32024
H.264(4): 32034
Unicast port (Audio)
Usable port number range:
1024 to 50000
●
Only even numbers can be specified.
●
The port number cannot be set to 10670.
Factory settings:
H.264(1): 33004
H.264(2): 33014
H.264(3): 33024
H.264(4): 33034
●
The unicast port number must be configured
when [Transmission type] is set to [Unicast port
(MANUAL)].
Note
Multicast address
Enter the multicast IP address.
Images and audio will be sent to the specified IP address.
Usable values:
IPv4: 224.0.0.0 to 239.255.255.255
IPv6: Multicast address starting with FF.
Factory settings:
H.264(1): 239.192.0.20
H.264(2): 239.192.0.21
H.264(3): 239.192.0.22
H.264(4): 239.192.0.23
●
Verify usable multicast IP addresses before entering
this setting.
Note
Multicast port
Enter the multicast port number (used when sending
images from the unit).
Usable port number range:
1024 to 50000
●
Only even numbers can be specified.
●
The port number cannot be set to 10670.
Factory settings:
37004
●
When sending audio from the unit, a port number
with “1000” added to the multicast port number will
be used.
Note
Multicast TTL/HOP Limit
Enter the TTL/HOPLimit value for multicast.
Usable values:
1 to 254
Factory settings:
16
●
When transmitting H.264 images via the Internet,
transmitted images may not appear depending on
proxy server settings, firewall settings, etc. In such
cases, consult your network administrator.
●
When displaying multicast images on a personal
computer with multiple LAN cards installed, disable
the LAN cards that are not used for reception.
Notes
●
IP control can be performed but if you do not want
to perform IP image transmission, set “JPEG
transmission”, “H.264 transmission” and “Audio
Transmission” to “Off”.
In this case, IP images will also not be displayed on the
mobile terminal.
Note
Summary of Contents for AW-HE38HKPC
Page 139: ...139 Memo ...
Page 140: ...Web Site http www panasonic com Panasonic Corporation 2017 ...
