manualshive.com logo in svg

Panasonic AFP7CCM1, User Manual

Share
Download
Panasonic AFP7CCM1 User Manual Download Page 81

7.4 MEWTOCOL-COM Master Communication (SEND) 

 

7-11 

7.4.2  SEND Instruction (When MEWTOCOL-COM is Used) 

 

Instruction format 

 

Setting 
items 

Settings 

Setting range 

i 

Specify the operation unit. 

US / SS 

S 

Specify the header of the source node data area. (Note 1) 

- 

n 

Specify the No. of sent data. 

1 - 507 words  
or 1 bit 

D1 

Specify the partner station no. (Note 2) (Note 3) 

0 - 99  

D2 

Specify the initial address of the receiver node data area in the partner 
node. (Note 4) 

0 - 99999 

D3 

Specify the device area in the source node to save the execution result 
code (one word). 

(Note 5) 

(Note 1) Transmission methods vary by the type of device to be specified for the operands [S] and [D2]. 

Device to be specified for [S2] and [D1] 

Transmission 

method 

16 bit device: WX, WY, WR, WL, DT, LD 

Register 
transmission 

1 bit device: X, Y, R, L, DT, n, LD, n 

Bit transmission 

(Note 2) The No. of sent data is on a word basis for register transmission, and on a bit basis for bit transmission. 

(Note 3) When "0" is specified for partner station no., global transmission is applied. In this case, no response 

message is received from the partner side. 

(Note 4) Bit device DT, n and LD, n cannot be specified for the header of the receiver data in the partner node. 

(Note 5): Device that can be specified for [D3] are: WX, WY, WR, WL, DT, LD. Saved as one word in the specified area.  

0: Normal completion 
1: Communication port is being used for master communication 
2: Communication port is being used for slave communication 
3: No. of master communication instructions that can be used simultaneously has been exceeded 
4: Sending timeout 
5: Response reception timeout 
6: Received data error 

 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7CCM1












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands