manualshive.com logo in svg

Panasonic AFP7CCM1, User Manual

Share
Download
Panasonic AFP7CCM1 User Manual Download Page 18

Functions of Units and Restrictions on Combination 

1-8 

 

1.3  Restrictions on Units Combination 

1.3.1  Restrictions on the Number of Installed Units 

There are following restrictions depending on units to be used. 

Unit type 

Number of installed units 

Remarks 

Serial Communication Unit 

Max. 8 units 

 

1.3.2  Restrictions on the Combination of Extension Cassettes 

(Communication Cassettes) 

 One communication cassette can be attached to the CPU unit, and two communication 

cassettes to the serial communication unit. 

 The FP7 communication cassette (Ethernet type) can be attached to the CPU only. It cannot 

be attached to the serial communication unit (SCU). 

1.3.3  Restrictions on Communication Functions to be Used 

There are the following restrictions on functions to be used when using the SCU or ET-LAN 
that is built in the CPU unit, or the serial communication unit (SCU). 

Function to be used 

Restrictions 

PLC link function 

Up to two communication ports can be used. For using two ports, allocate 
different link areas to them. 

CPU with built-in SCU (COM.1 port) 

Serial communication unit (COM.1 port) 

MEWTOCOL-COM master 

MODBUS-RTU master 

A maximum of 16 communication ports and the number of connections in 
combination can be used simultaneously. 

CPU with built-in SCU (COM.1 port to COM. 2 port) 

Serial communication unit (COM.1 port to COM.4 port) 

CPU with built-in ET-LAN (User connections 1 to 16) 

MEWTOCOL-COM slave 

MEWTOCOL7-COM slave 

MODBUS-RTU slave 

A maximum of 15 communication ports and the number of connections in 
combination can be used simultaneously. 

CPU with built-in SCU (COM.1 port to COM. 2 port) 

Serial communication unit (COM.1 port to COM.4 port) 

CPU with built-in ET-LAN  

(System connections 1 to 4 / User connections 1 to 16) 

General-purpose 
communication 

There is no restriction. 

1.3.4  Unit to be Used and Applicable Versions of CPU Unit and FPWIN GR7 

For using the unit, the following versions of CPU unit and FPWINGR7 are required. 

Applicable versions 

Unit type 

CPU unit 

FPWINGR7 

Remarks 

FP7 Serial Communication Unit 

Ver.1.2 or later 

Ver.1.3 or later 

 

 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7CCM1












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands