manualshive.com logo in svg

Panasonic AFP7CCM1, User Manual

Share
Download
Panasonic AFP7CCM1 User Manual Download Page 46

I/O Allocation 

4-2 

 

4.1 Input/Output Signals Used for Communication 

4.1.1  I/O Allocation of CPU Unit 

 

Input signal 

Input 

signal 

Communication 

port 

Name 

Description 

Effective 

operation 

mode 

X0 

For COM.1 Port 

X1 

For COM.2 Port 

X2 

For COM.0 Port 

General-
purpose 
communication 
Reception 
done flag 

When the unit completes the data reception, 
it turns on (1). 

Waiting for data reception: 0, Reception 
completed: 1 

General-
purpose 
communication 

X3 

- 

Not used 

Do not use this. 

 

X4 

For COM.1 Port 

X5 

For COM.2 Port 

X6 

For COM.0 Port 

General-
purpose 
communication 
Reception 
done (copy) 
flag 

It turns on (1) if there are copied data when 
GPRECV instruction is executed. It turns off 
(0) when END instruction is executed.  
(Note 1) 
Reading completed: 1 
No data to be read: 0 

General-
purpose 
communication 

X7 

- 

Not used 

Do not use this. 

 

X8 

For COM.1 Port 

X9 

For COM.2 Port 

XA 

For COM.0 Port 

General-
purpose 
communication 
Clear to send 
flag 

It turns on (1) when the unit is set to the 
general-purpose communication mode. It 
turns off (0) in other modes. 

General-
purpose 
communication 

XB 

- 

Not used 

Do not use this. 

 

XC 

For COM.1 Port 

XD 

For COM.2 Port 

XE 

For COM.0 Port 

Master 
communication 
Clear to send 
flag 

It turns on (1) when the unit is set to modes 
other than the PLC link mode or general-
purpose communication mode. It turns off (0) 
in other modes. 

MEWTOCOL 
MODBUS-RTU 

XF 

- 

Not used 

Do not use this. 

 

X10 

For COM.1 Port 

X11 

For COM.2 Port 

X12 

For COM.0 Port 

Reset done 

When the communication channel is reset 
under the output Y10 - Y12, the flag is 
turned on (1) once the resetting operation is 
completed. 
Resetting done: 1 
Y10 - Y12 is off: 0 

General-
purpose 
communication 

X13 

- 

Not used 

Do not use this. 

 

X14 

For COM.1 Port 

CTS signal 
monitor 

Status of the CTS signal sent from the 
device communicating with. 

Clear to send from COM.1 port = 0 
Cannot send from COM.1 port = 1 

The RTS signal can be controlled with Y14. 

When RS/CS is 
set to valid in 
Communication 
Block COM.1. 

X15 
- X1F 

- 

Not used 

Do not use this. 

 

(Note 1) The general-purpose communication reception done (copy) flag is effective after the execution of the RECV 

instruction until one of the following instructions is executed. This flag does not remain ON across several scans. 
Execute 1: END instruction (scan header), and 2: RECV instruction 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7CCM1












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands