manualshive.com logo in svg

Pall Allegro 1000 L, Instructions For Use Manual

Share
Download
Pall Allegro 1000 L Instructions For Use Manual Download Page 2

2

Table of Contents

1. Introduction ..................................................................................................................................................3

2. Warning ........................................................................................................................................................3

3. Receipt of Equipment..................................................................................................................................3

4. Installation and Operation ...........................................................................................................................3

4.1 Preparation and installation of the Allegro base and extension module ....................................................4

4.2 Preparation and installation of the hoist ..................................................................................................7

4.3 Installation of the Allegro biocontainer/system........................................................................................10

4.4 Filling the Allegro biocontainer/system ..................................................................................................11

4.5 Draining the Allegro biocontainer ..........................................................................................................13

4.5.1 From the bottom (1000 L, 2000 L, and 3000 L) ..........................................................................13

4.5.2 From the Top (1000 L only) ..........................................................................................................13

4.6 Removing Allegro 3D biocontainer from the Allegro tote ........................................................................13

5. Allegro Biocontainer Replacement ...........................................................................................................13

6. Troubleshooting Guide ..............................................................................................................................13

7. Scientific and Laboratory Services ...........................................................................................................14

8. Warranty .....................................................................................................................................................14

Summary of Contents for Allegro 1000 L















Reviews:

No comments

Brands by name

Popular brands

Load more brands