Palfinger ILP 25 Installation Manual Download Page 23 | Manualshive

Page: 23 / 65

background image

ILP 25/33 Installation Manual

Rev. 1.4

- 23 -

2. Use a forklift, hoist or equivalent to support the bed extension and align the bed extension with the

pre-drilled hole pattern on the sill. Verify the bed extension is squared. Secure the bed extension to
the sill with the provided 9/16

x1.75” bolts and 9/16” nuts. Torque all bolts to 125 ft./lbs. min.,

145 ft./lbs. max.

Recommendation: It is highly recommended to lubricate all bolts and nuts prior to

installation.

Bed
Extension

Sill

7/8"
Wrench

13/16"
Impact Socket

Bolt-On Bed Extension

«
...
21
22
23
24
25
...
»

Summary of Contents for ILP 25


































































Reviews:

No comments

Related manuals for ILP 25

Brand: Abicor Binzel Pages: 42

Century 2 NCL10000 Series

Brand: BraunAbility Pages: 39

Brand: Keg King Pages: 4

SystemRoMedic EvaDrive450

Brand: Handicare Pages: 37

Brand: gala gar Pages: 28

Brand: M-system Pages: 5

R1000 series E20

Brand: Roland Pages: 156

Brand: Paton Pages: 17

Brand: Riello Pages: 2

Brand: Air Liquide Pages: 66

Brand: Bear Pages: 21

Brand: Firepower Pages: 32

Marine Pro RIO 216

Brand: auto maskin Pages: 11

Brand: M-system Pages: 7

AC AUTO STOP GEN 2

Brand: Lift Tech Marine Pages: 2

Brand: MESA Electronic Pages: 19

Brand: M-system Pages: 5

Brand: EWM Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands