Palax D410 Pro+ Instruction Manual Download Page 8

Page: 8 / 43

Palax D410 Pro+

Translation

1-2020

Lifting point for loader

Lifting point

The machine may

only be operated by

one person

Keep clear of the

machine´s moving parts

Beware of the PTO shaft

The danger zone around the conveyor is 5

meters

Disconnect the machine

from the power source

before servicing

Nameplates

Nameplate on the machine



The name and address of the manufacturer



Designation of the machine type



Serial number and year of manufacture



Total weight of the machine



The plate is located at the in-feed conveyor end

of the machine.



When ordering spare parts, always mention the

serial number and year of manufacture.

Nameplates on the electric drive



3-phase motor



Voltage 230/380 V or 380/600 V, may vary depending on the country.



Output 11 kW, fuse size min. 25 A slow. Recommendation 32 A slow.



The plate is located on the connecting box of the electric motor.

Summary of Contents for D410 Pro+












































Search results

Summary of Contents for D410 Pro+

Reviews:

Related manuals for D410 Pro+

Brands by name

Popular brands

Palax D410 Pro+, Instruction Manual

Search results

Summary of Contents for D410 Pro+

Reviews:

Related manuals for D410 Pro+

Brands by name

Popular brands