Packard Bell EasyNote LJ75 Service Manual Download

Page: 53 / 222

Chapter 2

Remove HDD/BIOS Password Utilities

This section provides you with details about removing HDD/BIOS password:

Remove HDD Password:

If you key in the wrong HDD password three times, an error is generated.

To reset the HDD password, perform the following steps:

After the error is displayed, select the

Enter Unlock Password

option on the screen.

An Encode key is generated for unlocking utilities. Note down this key.

Execute the

UnlockHD.EXE

file to create the unlock code in DOS Mode using the format

UnlockHD

[Encode code]

with the code noted in the previous step, as follows:

UnlockHD 76943488

The command generates a password which can be used for unlocking the HDD.

Password: 46548274

Key in the password from the previous step to unlock the HDD as shown.

All manuals and user guides at all-guides.com

Summary of Contents for Bell EasyNote LJ75































































































































































































































Search results

Summary of Contents for Bell EasyNote LJ75

Reviews:

Related manuals for Bell EasyNote LJ75

Brands by name

Popular brands

Packard Bell EasyNote LJ75, Service Manual

Search results

Summary of Contents for Bell EasyNote LJ75

Reviews:

Related manuals for Bell EasyNote LJ75

Brands by name

Popular brands