Packard Bell EasyNote LJ75 Service Manual Download

Page: 171 / 222

Chapter 4

161

Post Codes

These tables describe the POST codes and descriptions during the POST.

Chipset POST Codes

The following table details the chipset POST codes and functions used in the POST.

Sec:

NO_EVICTION_MODE_DEBUG EQU 1 (CommonPlatform\sec\Ia32\SecCore.inc)

Memory:

DEBUG_BIOS equ 1 (Chipset\Alviso\MemoryInitAsm\IA32\IMEMORY.INC)

Code

Description

0xC2

MTRR setup

0xC3

Enable cache

0xC4

Establish cache tags

0xC5

Enter NEM, Place the BSP in No Fill mode, set CR0.CD = 1, CR0.NW = 0.

0xCF

Cache Init Finished

Code

Description

0xA0

First memory check point

0x01

Enable MCHBAR

0x02

Check for DRAM initialization interrupt and reset fail

0x03

Verify all DIMMs are DDR or DDR2 and unbuffered

0x04

Detect an improper warm reset and handle

0x05

Detect if ECC SO-DIMMs are present in the system

0x06

Verify all DIMMs are single or double sided and not asymmetric

0x07

Verify all DIMMs are x8 or x16 width

0x08

Find a common CAS latency between the DIMMS and the MCH

0x09

Determine the memory frequency and CAS latency to program

0x10

Determine the smallest common TRAS for all DIMMs

0x11

Determine the smallest common TRP for all DIMMs

0x12

Determine the smallest common TRCD for all DIMMs

0x13

Determine the smallest refresh period for all DIMMs

0x14

Verify burst length of 8 is supported by all DIMMs

0x15

Determine the smallest tWR supported by all DIMMs

0x16

Determine DIMM size parameters

0x17

Program the correct system memory frequency

0x18

Determine and set the mode of operation for the memory channels

0x19

Program clock crossing registers

0x20

Disable Fast Dispatch

0x21

Program the DRAM Row Attributes and DRAM Row Boundary registers

0x22

Program the DRAM Bank Architecture register

0x23

Program the DRAM Timing & and DRAM Control registers

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Bell EasyNote LJ75































































































































































































































Search results

Summary of Contents for Bell EasyNote LJ75

Reviews:

Related manuals for Bell EasyNote LJ75

Brands by name

Popular brands

Packard Bell EasyNote LJ75, Service Manual

Search results

Summary of Contents for Bell EasyNote LJ75

Reviews:

Related manuals for Bell EasyNote LJ75

Brands by name

Popular brands