Packard Bell EasyNote LJ75 Service Manual Download

Page: 59 / 222

Chapter 3

Machine Disassembly and Replacement

IMPORTANT:

The outside housing and color may vary from the mass produced model.

This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.

Disassembly Requirements

To disassemble the computer, you need the following tools:

•

Wrist grounding strap and conductive mat for preventing electrostatic discharge

•

Flat screwdriver

•

Philips screwdriver

•

Plastic flat screwdriver

•

Plastic tweezers

NOTE:

The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.

Chapter 3

Summary of Contents for EasyNote LJ75































































































































































































































Search results

Summary of Contents for EasyNote LJ75

Reviews:

Related manuals for EasyNote LJ75

Brands by name

Popular brands

Packard Bell EasyNote LJ75, Service Manual

Search results

Summary of Contents for EasyNote LJ75

Reviews:

Related manuals for EasyNote LJ75

Brands by name

Popular brands