Packard Bell EasyNote LJ75 Service Manual Download

Page: 49 / 222

Chapter 2

BIOS Flash Utilities

The BIOS flash memory update is required for the following conditions:

•

New versions of system programs

•

New features or options

•

Restore a BIOS when it becomes corrupted.

Use the Phlash utility to update the system BIOS flash ROM.

NOTE:

If you do not have a crisis recovery diskette at hand, then you should create a

Crisis Recovery

Diskette

before you use the Phlash utility.

NOTE:

Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.

NOTE:

Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not

contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.

Fellow the steps below to run the Phlash.

Prepare a bootable diskette.

Copy the flash utilities to the bootable diskette.

Then boot the system from the bootable diskette. The flash utility has auto-execution function.

Summary of Contents for EasyNote LJ75































































































































































































































Search results

Summary of Contents for EasyNote LJ75

Reviews:

Related manuals for EasyNote LJ75

Brands by name

Popular brands

Packard Bell EasyNote LJ75, Service Manual

Search results

Summary of Contents for EasyNote LJ75

Reviews:

Related manuals for EasyNote LJ75

Brands by name

Popular brands