Packard Bell EasyNote LJ75 Service Manual Download

Page: 13 / 222

Chapter 1

•

802.11b/g/n Wi-Fi CERTIFIED™

•

802.11b/g Wi-Fi CERTIFIED™

•

WPAN*: Bluetooth® 2.1+EDR

•

LAN: Gigabit Ethernet, Wake-on-LAN ready

•

Modem: 56K ITU V.92 with PTT approval*

Privacy control

•

BIOS user, supervisor, HDD passwords

•

Kensington lock slot

Power

•

ACPI 3.0 CPU power management standard: supports Standby and Hibernation power-saving
modes

•

4400 mAh 6-cell Li-ion battery pack with integrated graphics:

•

3-hour 10-minute battery life*

•

3-pin 65 W AC adapter

•

4400 mAh 6-cell Li-ion battery pack with discrete graphics:

•

2-hour 50-minute battery life*

•

3-pin 90 W AC adapter

•

ENERGY STAR®

Special Keys and Controls

•

99-/100-/103-key keyboard

•

Multi-gesture touchpad, supporting two-finger scroll, pinch, rotate, flip

•

Nine function keys, four cursor keys, Windows® key, international language support

•

Capacitive-touch launch keys: programmable, backup, touchpad lock, WLAN, volume up/down/
mute

I/O Ports

•

Multi-in-1 card reader

•

Four USB 2.0 ports

•

HDMI™ port with HDCP support*

•

External display (VGA) port

•

Headphone/speaker/line-out jacks with S/PDIF support

•

Microphone-in jack

•

Ethernet (RJ-45) port

•

Modem (RJ-11) port*

•

DC-in jack for AC adapter

Software*

•

Packard Bell Customer Registration

•

Packard Bell Identity Card

Summary of Contents for EasyNote LJ75































































































































































































































Search results

Summary of Contents for EasyNote LJ75

Reviews:

Related manuals for EasyNote LJ75

Brands by name

Popular brands

Packard Bell EasyNote LJ75, Service Manual

Search results

Summary of Contents for EasyNote LJ75

Reviews:

Related manuals for EasyNote LJ75

Brands by name

Popular brands