Pacific Power Source AMX Series Operation Manual Download

Page: 92 / 114

SECTION 4 OPERATION

4.3 ROUTINE

POWER-UP

The following procedure is recommended to turn-on paralleled systems after it has been
verified that the installation is correct.

Set the OUTPUT POWER switch to the

OFF

position.

Switch the INPUT POWER switch to the

position. The controller will light up and

begin to display output data. The value of the output parameters will be set as
programmed in the UPC.

Set the OUTPUT POWER switch to the

ON/AUTO

position and the OUTPUT

ENABLE button of the UPC must be

CAUTION

DO NOT CONNECT ANY LOADS TO THE OUTPUT OF THE POWER SOURCE UNTIL THE OUTPUT

VOLTAGE AND FREQUENCY HAVE BEEN VERIFIED AS CORRECT.

APPLICATION OF IMPROPER VOLTAGE OR FREQUENCY CAN DAMAGE USER LOADS.

WARNING

LETHAL VOLTAGES ARE PRESENT AT THE OUTPUT TERMINALS OF THIS MACHINE!

Summary of Contents for AMX Series



















































































































Search results

Summary of Contents for AMX Series

Reviews:

Related manuals for AMX Series

Brands by name

Popular brands

Pacific Power Source AMX Series, Operation Manual

Search results

Summary of Contents for AMX Series

Reviews:

Related manuals for AMX Series

Brands by name

Popular brands