background image

January 20, 2020
©  S&C Electric Company 1999-2020, all rights reserved

Instruction Sheet  682-510

Remote Supervisory Vista

®

 Underground Distribution Switchgear

Pad-Mounted, Dry-Vault-Mounted, Wet-Vault-Mounted, and Undercover™ Styles

Introduction

Qualified Persons   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Read this Instruction Sheet    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Retain this Instruction Sheet .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  2
Proper Application    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Warranty   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2

Safety Information

Understanding Safety-Alert Messages  .  .  .  .  .  .  .  .  .  .  . 3
Following Safety Instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Replacement Instructions and Labels    .  .  .  .  .  .  .  .  .  .  . 3
Location of Safety Labels   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

Safety Precautions

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5

Components

Overview of Components   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Understanding the Gas Pressure Gauge   .  .  .  .  .  .  .  .  . 9
Gauge Needle Fluctuations from Rapid 
   Ambient Temperature Changes  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9

Operation

Manually Opening, Closing, or Grounding a Way    .  .10
Locking Out Grounded Position   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .14
Locking In Closed, Open, or Grounded Position   .  .  .15

Electrically Opening, Closing, or 
  Grounding a Way    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .16
Motor Operator Decoupling    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 20
Checking for Voltage Using Optional 
   VOLTAGE Indicator   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 22
Low-Voltage Phasing Using Optional 
   VOLTAGE Indicator with Phasing    .  .  .  .  .  .  .  .  .  .  .  . 25

Maintenance

Components   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 27
Returning Equipment to Service  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 28
Enclosure Finish   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 28
Maintenance Recommendations in 
  Extremely Corrosive Environments    .  .  .  .  .  .  .  .  .  .  . 29

Dielectric Testing

Routine Switchgear Testing   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 30
Cable Testing and Fault Locating   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .31
Fault Interrupter Testing   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  31
Resistance Measurement  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 32

Section Page

Section Page

Table of Contents

Operation

Summary of Contents for Remote Supervisory Vista

































Reviews: