Pacific Power Source AMX Series Operation Manual Download

Page: 94 / 114

SECTION 4 OPERATION

4.4 SYSTEM

TURN-OFF

This paragraph describes the procedure used to turn off the AMX-Series Power Source.

The AMX-Series Power Source is turned off by:

Setting the OUTPUT POWER Switch to the

OFF

position.

Opening the INPUT POWER circuit breaker

4.4.1 SYSTEM TURN-OFF, MODELS 390 and 3120-AMX

This paragraph describes the procedure used to turn off the 390 and 3120-AMX Power
Sources.

The 390 and 3120-AMX Power Sources are turned off by:

Setting the OUTPUT POWER Switch of the Master chassis (which has the controller
installed) to the

OFF

position.

Opening the INPUT POWER circuit breaker of the Slave chassis.

Opening the INPUT POWER circuit breaker of the Master chassis.

CAUTION

It is recommended that only the OUTPUT POWER switch of the Master chassis be used to remove

power to a load. The INPUT POWER switch of the Slave chassis should never be turned to the

OFF

position with a load attached to the system as it will subject the Master chassis to all the load current

being delivered by the system. This will cause an overtemp shutdown if the load exceeds the Master

chassis' system ratings. Also, the Master chassis INPUT POWER switch should never be used to

remove power to a load since it drives all the control circuits for the paralleled system.

Summary of Contents for AMX Series



















































































































Search results

Summary of Contents for AMX Series

Reviews:

Related manuals for AMX Series

Brands by name

Popular brands

Pacific Power Source AMX Series, Operation Manual

Search results

Summary of Contents for AMX Series

Reviews:

Related manuals for AMX Series

Brands by name

Popular brands