Pacific energy FP30 LE Installation And Operating Instructions Manual Download Page 45

 Rating Label 

• 

•  LE SYSTÈME DE CHEMINÉE DOIT ÊTRE HOMOLOGUÉ COMME SUIT : AU CANADA - CHEMINÉE HOMOLOGUÉE ULC-S-629, 

LE SYSTÈME DE CHEMINÉE DOIT ÊTRE HOMOLOGUÉ COMME SUIT : AU CANADA - CHEMINÉE HOMOLOGUÉE ULC-S-629,  

•  INSTALLEZ ET UTILISEZ SELON LES INSTRUCTIONS D’INSTALLATION ET D’UTILISATION FOURNIES AVEC LE FOYER.

•  LES PARTIES DU FOYER INCORPORANT DES CONDUITS CHAUDS OU FROIDS DOIVENT ÊTRE ENCHÂSSÉES, CONFORMÉMENT AUX IN-

STRUCTIONS D’INSTALLATION ET D’UTILISATION FOURNIES AVEC LE FOYER.

•  CONTACTEZ LES AGENTS LOCAUX DU CODE DU BÂTIMENT OU DU SERVICE-INCENDIE POUR LES RESTRICTIONS, PERMIS D’INSTALLATION 

ET EXIGENCES D’INSPECTION DANS VOTRE RÉGION.

•  NE RACCORDEZ PAS CE FOYER À UN CONDUIT DE CHEMINÉE DESSERVANT UN AUTRE APPAREIL.

•  NE PAS OBSTRUER PAS LES OUVERTURES DEVANT LE FOYER, NI RESTREINDRE L’ALIMENTATION D’AIR NÉCESSAIRE POUR LE FONC-

TIONNEMENT NORMAL DU FOYER, TEL QUE SPÉCIFIÉ DANS LES INSTRUCTIONS D’INSTALLATION ET D’UTILISATION FOURNIES AVEC 

L’APPAREIL. LA PROVISION INADEQUATE D’AIR POUR COMBUSTION, MAI DE VENTILATION ET DILUTION A POUR RESULTAT L’OPERATION 

DANGEREUSE DE CECI ET AUTRES APPAREILS.

•   VOIR LE CODE DU BÂTIMENT LOCAL ET LES INSTRUCTIONS DU FABRICANT, POUR LES PRÉCAUTIONS EXIGÉES LORSQU’UNE CHEMINÉE 

TRAVERSE UN MUR OU PLAFOND EN MATÉRIAUX COMBUSTIBLES.

•  REMPLACEZ LA VITRE SEULEMENT PAR UNE VITRE EN CÉRAMIQUE. •  LA SOUFFLERIE CLASSEMENT ELECTRIQUE 115V, 60 Hz, 1.1AMP

•  CETTE CHEMINEE n’A pas ETE ESSAYEE AVEC UN UNVENTED JOURNAL DE GAZ A REGLE. POUR REDUIRE LE RISQUE DE FEU OU BLESS-

URE, LE PAS INSTALLE UN UNVENTED JOURNAL DE GAZ A REGLE DANS CHEMINEE. 

•   UTILISEZ SEULEMENT AVEC LA PORTE DE CHARGEMENT FERMÉE. NE L’OUVREZ QUE POUR ALIMENTER LE FEU.

•  CE FOYER PEUT ÊTRE INSTALLÉ DANS UNE MAISON PRÉFABRIQUÉE. UTILISER DU BOIS SOLIDE SEULEMENT.

•  POUR COMBUSTIBLE SOLIDE SEULEMENT.

•   COMPOSANTS OPTIONNELS: KIT DE CONDUITS DE DISTRIBUTION DE CHALEUR (PIÈCE no WODC.RHKA).

•   UTILISEZ LES COMPOSANTS SPÉCIFIÉS DANS LES INSTRUCTIONS D’INSTALLATION DE PACIFIC ENERGY.

MODEL/ MODÈLE:  

FP30 LE          FP30AR LE     

LISTED FACTORY BUILT FIREPLACE. 

Also for use in Mobile Homes

CERTIFIED TO / CERTIFIÉ POUR; 

ULC S610 AND UL 127 for CANADA AND U.S.A.

• •    ALSO FOR USE IN MANUFACTURED HOMES WITH SOLID WOOD FUEL ONLY 

•  INSTALL AND USE IN ACCORDANCE WITH THE INSTALLATION AND OPERATING INSTRUCTIONS SUPPLIED WITH THE APPLIANCE

•  AREAS OF THE FIREPLACE INCORPORATING WARM OR COLD AIR DUCTS SHALL BE ENCLOSED IN ACCORDANCE WITH THE INSTALLA-

TION AND OPERATING INSTRUCTIONS SUPPLIED WITH THE APPLIANCE.  

•  CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS, INSTALLATION PERMIT AND INSPECTION IN YOUR AREA. 

•  DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE 

•  DO NOT OBSTRUCT THE OPENINGS IN FRONT OF THE FIREPLACE OR OTHERWISE RESTRICT SUPPLY AIR NECESSARY FOR NORMAL FIRE-

PLACE OPERATION AS SPECIFIED IN INSTALLATION AND OPERATING INSTRUCTIONS SUPPLIED WITH THE APPLIANCE. INADEQUATE AIR 

SUPPLY FOR COMBUSTION, VENTILATION AND DILUTION MAY RESULT IN DANGEROUS OPERATION OF THIS AND OTHER APPLIANCES.

•  CHIMNEY SYSTEM MUST BE LISTED TO: ULC S-629 IN CANADA / UL-103 HT IN USA    - 

ULC S-629 IN CANADA / UL-103 HT IN USA    - SEE LOCAL BUILDING CODE AND MANUFACTURER'S 

INSTRUCTIONS FOR PRECAUTIONS REQUIRED WHEN PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING.    

•  OPTIONAL COMPONENTS: REMOTE HEAT KIT PART# WODC.RHKA. 

•  USE SOLID WOOD FUEL ONLY. OPERATE ONLY WITH FEED DOOR CLOSED.  OPEN TO FEED FIRE ONLY.

•  BLOWER ELECTRICAL RATING 115V, 60HZ, 1.1AMP   • REPLACE GLASS ONLY WITH 5mm CERAMIC GLASS.

•  DO NOT USE OR INSTALL COMPONENTS OR PRODUCTS NOT SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS. 

•  DO NOT USE A FIREPLACE INSERT OR OTHER PRODUCTS NOT SPECIFIED FOR USE WITH THIS PRODUCT.

•  THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED GAS LOG SET. TO REDUCE RISK OF FIRE OR INJURY, DO NOT INSTALL AN 

UNVENTED GAS LOG SET INTO FIREPLACE.  

•  THIS WOOD HEATER NEEDS PERIODIC INSPECTION AND REPAIR FOR PROPER OPERATION. 

•        - CONSULT THE OWNER’S MANUAL FOR FURTHER INFORMATION.

•  IT IS AGAINST FEDERAL REGULATIONS TO OPERATE THIS WOOD HEATER IN A MANNER INCONSISTANT WITH THE OPERATING 

INSTRUCTIONS IN THE OWNER’S MANUAL.

DO NOT REMOVE THIS LABEL/ NE RETIREZ PAS CETTE ÉTIQUETTE

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS/ DÉGAGEMENTS MINIMUMS AUX MATÉRIAUX COMBUSTIBLES

ETL#4001507

MANUFACTURED BY/ FABRIQUÉ PAR :

PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

2975 ALLENBY RD., DUNCAN, BC  V9L 6V8

MADE IN CANADA 

/ FABRIQUÉ AU CANADA

040523

100004188

            MANTEL HEIGHT MUST  BE MEASURED FROM THE BASE OF THE UNIT AS FOLLOWS: 51”(1.3m) FOR A 4”(102mm) DEEP MANTEL UP TO 

55”(1.4m) FOR A 12”(305mm) DEEP MANTEL. SEE THE INSTALLATION INSTRUCTIONS FOR GRADUATED MANTEL HEIGHTS MEASURMENTS 

FOR DEPTHS BETWEEN 4”(102mm) AND 12”(305mm).// LA HAUTEUR DU MANTEAU, MESURÉE À PARTIR DE LA BASE DE L’APPAREIL, DOIT 

AVOIR : 51 po (1295 mm) POUR UN MANTEAU DE 4 po (102 mm) DE PROFONDEUR, ET 55 po (1397 mm) POUR UN MANTEAU DE 12 po (305 mm) 

DE PROFONDEUR.  POUR LES PROFONDEURS DE MANTEAU COMPRISES ENTRE 4 po (102 mm) ET 12 po (305 mm), VOIR LES INSTRUCTIONS 

D’INSTALLATION ET D’UTILISATION (TABLEAU GRADUEL DES DIMENSIONS DE MANTEAUX).

***

1.7

g/hr.

Refer to Intertek’s Directory of Building Products for detailed information

DATE OF MANUFACTURE

CLEARANCES TO SIDE AND BACK STANDOFFS/ DÉGAGEMENTS                     

     

0 in. / 0 mm

A. CORNER TO SIDEWALL/ COIN AU MUR LAT. 

                                        

     5 3/8in. / 137mm

B. CEILING TO UNIT/ DU PLAFOND AU FOYER
NON-COMBUSTIBLES ONLY IN THE SPACE ABOVE UNIT TO CEILING, NOT INCLUDING 
APPROVED FRAMING / NON-COMBUSTIBLES SEULEMENT AU-DESSUS FOYER À PLAFOND                                                               
C. BASE OF UNIT TO MANTEL/ BASE DE L’UNITÉ AU MANTEAU  

 

37 in. /940mm 

D. EMBER PROTECTION FROM FRONT OF UNIT/ 
  PROTECTEUR de PLANCHER À L’AVANT DU FOYER                      

          18 in. / 457 mm

F.  EMBER PROTECTION TO SIDE OF UNIT/ 
  PROTECTEUR de PLANCHER AU CÔTÉ DU FOYER                                                                            8 in. /203 mm

IN USA: Type 1 floor protector - approved to UL1618 - Minimum 20GA steel  

***

U.S. ENVIRONMENTAL PROTECTION AGENCY 

Certified to comply with 2020 particulate 

emission standards, 

using Cordwood. 

Tested to ASTM 3053

B

A

C

D

CAN.

U.S.A.

E

E

B

45

100004186_040523-48

FP30 LE

Summary of Contents for FP30 LE

















































Reviews: