background image

CAUTION:  Hot while in operation.  Keep children, clothing and furniture away.  Contact may cause skin 
burns.

WARNING: Always keep loading door closed when burning. This heater is not designed for open door 
burning.

WARNING:  No alteration or modification of the combustion air control assembly is permitted.  Any 
tampering will void warranty and could be very hazardous.

WARNING:  Do not use grates or andirons to elevate the fuel.  Burn directly on the fire bricks.  Replace 
broken or missing bricks.  Failure to do so may create a hazardous condition.

Wood Selection

This heater is designed to burn natural wood only. Higher efficiency and lower emissions generally result when 
burning air-dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.

Wood should be properly air dried (seasoned) for six months or more. Wet or undried wood will cause 
the fire to smoulder and produce large amounts of smoke and creosote. Wet wood also produces very 
little heat and tends to go out often.  Wood should be stored under cover away from open flame or heat 
sources.

DO NOT BURN :

•  Salt water wood  *

•  Treated wood

•  Wet or green wood

•  Coal/charcoal

•  Garbage*

•  Solvents

•  Lawn clippings/yard waste

•  Unseasoned wood

•  Railroad ties

•  Manure or animal remains

•  Materials containing rubber, including tires

•  Materials containing plastic

•  Construction or demolition debris

•  Materials containing asbestos

•  Waste petroleum products, paints, paint thin-

ners, or asphalt products

•  Paper products, cardboard, plywood, or 

particleboard.

*  These materials contain chlorides which will rapidly destroy metal surfaces and void warranty.

Burning these materials may result in the release of toxic fumes or render the heater ineffective and cause 
smoke.

Do not burn anything but wood. Other fuels, eg. charcoal, can produce large amounts of carbon monoxide, a 
tasteless, odorless gas that can kill.  Under no circumstances should you attempt to barbecue in this heater.

The prohibition against burning these materials does not prohibit the use of fire starters made from paper, 
cardboard, saw dust, wax and similar substances for the purpose of starting a fire in an affected wood heater.

How  to Test Your Wood

Add a large piece of wood to the stove when it has a good large bed of coals. It is dry if it is burning on more 
than one side within one minute. It is damp if it turns black and lights within three minutes. If it sizzles, hisses 
and blackens without igniting in five minutes it is soaked and should not be burnt

 Operation 

ALT 4-LE 040523-28

6

100003978

Summary of Contents for ALDERLEA T4 LE





























Reviews: