background image

Check the following parts for damage such as cracks, excessive corrosion, burned out sections and 
excessive warping: (See website for descriptions and more detail)

Weekly:

•  Firebrick - Visual, for cracking.
•  Door Gasket - sagging, placement, damage.

Monthly 

•  Brick rail tabs and brick rails.
•  Air riser tube in the back of the firebox.
•  Back side of airwash chamber.
•  Baffle locking pin.
•  Boost openings.

When Cleaning the Chimney System:

•  Top baffle board/blanket.
•   Baffle.
•  Top heat shield and mounting bolt.
•  Baffle Gasket.
•  Brick Rails.
•  Manifold.

Blower:

•  The blower should be cleaned out a minimum every six months by using a vacuum on the grill openings in 

the back and bottom of the blower casing to remove any dust and debris.

Baffle:

•  Some warping of the baffle is normal (up to 1/4” or .65cm). Replace if the baffle has permanent warping 

greater than this or has cracking or breakage.

•  Please contact your Dealer if you experience any of the damage listed above. Continuing to operate your 

stove with broken parts may accelerate damage to other parts and may void your warranty

 Maintenance Checks 

ALT 4-LE 040523-28

10

100003978

Summary of Contents for ALDERLEA T4 LE





























Reviews: