Ozito X PXC PXGMTK-4182 Instruction Manual Download Page 35

Page: 35 / 40

TROUBLESHOOTING

Fault

Possible cause

Remedy

The motor does not start

Possible clogging

Clean the cutter head of any grass.

Battery is low charge.

Charge battery.

Battery not inserted properly.

Insert battery correctly.

Trimmer is not operating

at full capacity

Possible clogging

Clean the cutter head of any grass.

Cutting tall grass at ground level. Make several passes from top down.

Motor stops while

operating

Battery has no power

Charge battery

Grass wraps around the

shaft and trimmer head

Cutting tall grass at ground level. Make several passes from top down.

Pruner chain dry

No oil in the tank

Fill up with chain bar oil

Oil tank cap breather blocked

Clean the oil tank cap

Oil outlet blocked

Clean the oil outlet

Chain/guide bar hot

No oil in the tank

Fill up with oil

Oil tank cap breather blocked

Clean the oil tank cap

Oil outlet blocked

Clean the oil outlet

Blunt chain

Re-sharpen or replace chain

Chain is over tensioned

Check the chain tension

Pruner juddering, vibrating

or not sawing properly

Chain tension too loose

Adjust the chain tension

Blunt chain

Re-sharpen or replace chain

Worn chain

Replace the chain

Chain teeth pointing in wrong

direction

Reinstall the saw chain with the teeth facing in

the correct direction

Pruner wont cut

Blunt chain

Sharpen or replace chain

Chain on backwards (chain teeth

pointing in the wrong direction)

Remove chain and reinstall with the teeth facing

in the correct direction

Worn chain

Replace the chain

Summary of Contents for X PXC PXGMTK-4182









































Search results

Summary of Contents for X PXC PXGMTK-4182

Reviews:

Related manuals for X PXC PXGMTK-4182

Brands by name

Popular brands

Ozito X PXC PXGMTK-4182, Instruction Manual

Search results

Summary of Contents for X PXC PXGMTK-4182

Reviews:

Related manuals for X PXC PXGMTK-4182

Brands by name

Popular brands