Ozito X PXC PXGMTK-4182 Instruction Manual Download Page 31

Page: 31 / 40

Press

Spool housing

15cm

Press

Spool cover

Press

Spool housing

15cm

Press

Spool cover

Press

Spool housing

15cm

Press

Spool cover

Rewinding Spool from Bulk Line

Bulk line for your line trimmer is available from your local dealer. To install, follow steps:

1. Remove the spool as described in steps 1 - 3 of the

“Replacing the spool/clearing jams

and tangled lines”

section.

2. Cut a length of Ø2.0mm line, approximately 8m long.

3. Insert the new cutting line through the line mount inside the

spool.

4. Wind the line evenly with tension in a counterclockwise

direction.

5. To ensure that the line does not unravel while the spool

is being loaded, the line can be clipped into one of the

notches on the outer of the spool.

6. Thread the end of the line on the new line spool through the

eyelet in the spool cover.

7. Pull the line sharply to release it from notch.

8. Re-seat the spool as described in steps 5 - 6 of the

“

Replacing the spool/clearing jams and

tangled lines”

section.

Summary of Contents for X PXC PXGMTK-4182









































Search results

Summary of Contents for X PXC PXGMTK-4182

Reviews:

Related manuals for X PXC PXGMTK-4182

Brands by name

Popular brands

Ozito X PXC PXGMTK-4182, Instruction Manual

Search results

Summary of Contents for X PXC PXGMTK-4182

Reviews:

Related manuals for X PXC PXGMTK-4182

Brands by name

Popular brands