background image

7. RECOMMENDED SETUP cont.

Cleaning

Use a moist cloth to wipe down the pump housing. Allow to 

dry thoroughly before storing in a dry location that is protected 

from bad weather conditions.

Storage

If there is danger of frost, dismantle the device and 

accessories, clean and store them in a place protected from 

frost.

Dismantle and store

1.   Disconnect the device from 

the mains supply.

2.   Fully open any shut-off 

mechanisms (spray nozzles, 

valves, etc.) in the pressure 

line so that the air can 

escape without obstruction.

Note:

 Ensure the gate valve on 

your water tank is not left open 

as this will allow water to drain 

from the tank.

3.   Completely empty the pump by unscrewing the water drain 

plug.

4.   Dismantle the suction and pressure lines from the device.

5.   Store device in a frost-free room (at least 5 °C).

WARNING! 

MAKE SURE THE PUMP IS DISCONNECTED 

FROM ELECTRIC POWER SUPPLY BEFORE 

PERFORMING MAINTENANCE PROCEDURES.

WARNING! 

MAKE SURE THAT THE DEVICE AND 

CONNECTED ACCESSORIES ARE DEPRESSURIZED 

BEFORE CARRYING OUT ANY WORK ON THE DEVICE.

POTABLE

WATER

800W POTABLE WATER

 CONSTANT PRESSURE PUMP

MAINTENANCE

CONNECTION WITH TANK BASE BELOW WATER PUMP

P

CONNECTION WITH TANK BASE ABOVE THE WATER PUMP

 

 

CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP

FIRM BASE

SOLID STRUCTURE

WATERTANK

WATERTANK

NON-RETURN

VALVE

DISCHARGE

OUTLET

GATE 

VALVE

GATE 

VALVE

SUCTION LINE

SUCTION LINE

150mm

150mm

150mm

150mm

150mm

FIRM BASE

SOLID STRUCTURE

DISCHARGE

OUTLET

150mm

UNION 

COUPLING

depending on 

installation

UNION 

COUPLING

depending on 

installation

 

WATERTANK

GATE 

VALVE

SUCTION LINE

SOLID STRUCTURE

DISCHARGE

OUTLET

FIRM BASE

UNION 

COUPLING

depending on 

installation

IN-LINE

FILTER

IN-LINE

FILTER

IN-LINE

FILTER

POTABLE

WATER

POTABLE

WATER

POTABLE

WATER

INSTALLATION cont.

CONNECTION WITH TANK BASE BELOW WATER PUMP

P

CONNECTION WITH TANK BASE ABOVE THE WATER PUMP

 

 

CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP

FIRM BASE

SOLID STRUCTURE

WATERTANK

WATERTANK

NON-RETURN

VALVE

DISCHARGE

OUTLET

GATE 

VALVE

GATE 

VALVE

SUCTION LINE

SUCTION LINE

150mm

150mm

150mm

150mm

150mm

FIRM BASE

SOLID STRUCTURE

DISCHARGE

OUTLET

150mm

UNION 

COUPLING

depending on 

installation

UNION 

COUPLING

depending on 

installation

 

WATERTANK

GATE 

VALVE

SUCTION LINE

SOLID STRUCTURE

DISCHARGE

OUTLET

FIRM BASE

UNION 

COUPLING

depending on 

installation

IN-LINE

FILTER

IN-LINE

FILTER

IN-LINE

FILTER

POTABLE

WATER

POTABLE

WATER

POTABLE

WATER

Summary of Contents for CPPW-805









Reviews: