background image

size 445 x 210 mm

  

Danger!

 Read the operating instructions to  

reduce the risk of inquiry.

Beware of electrical voltage!

Caution! Wear ear-muffs.

 The impact of noise 

can cause damage to hearing.

Caution! Wear a breathing mask. 

Dust which 

is injurious to health can be generated when 

working on wood and other materials. Never use 

the device to work on any materials containing 

asbestos!

Caution! Wear safety goggles. 

Sparks gene-

rated during working or splinters, chips and dust 

emitted by the device can cause loss of sight.

The reprinting or reproduction by any other 

means, in whole or in part, of documentation and 

papers accompanying products is permitted only 

with the express consent of the iSC GmbH. 

Subject to technical changes

CMX-125U

GB

  Additonal operating & safety instructions Cement Mixer

Service information

We have competent service partners in all countries named on the guarantee certificate whose contact 

details can also be found on the guarantee certificate. These partners will help you with all service re

-

quests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the 

following parts are therefore also required for use as consumables.

Category

Example

Wear parts*

Rubber Gasket, Belt, Rubber Washer, Mixing 

Blades

Consumables*
Missing parts

* Not necessarily included in the scope of delivery!

In the effect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Plea

-

se ensure that you provide a precise description of the problem and answer the following questions in all 

cases:

• 

Did the equipment work at all or was it defective from the beginning?

• 

Did you notice anything (symptom or defect) prior to the failure?

• 

What malfunction does the equipment have in your opinion (main symptom)?   

Describe this malfunction.

Mayr/Product-Management

Weichselgartner/General-Manager

- 135 -

explains the following conformity according to EU directives and norms for 

the following product

Cement Mixer CMX-125U (Ozito)

   2014/29/EU 

 2005/32/EC_2009/125/EC 
 2014/35/EU 
 2006/28/EC 

X  2014/30/EU 

 2014/32/EU 
 2014/53/EC 
 2014/68/EU 
 90/396/EC_2009/142/EC 
 89/686/EC_96/58/EC 

X  2011/65/EU

 X  2006/42/EC

 Annex IV

Notifi ed Body:

Notifi ed Body No.:

Reg. No.:

X  2000/14/EC_2005/88/EC

X  Annex V

 Annex VI

 Noise: measured L

WA

 = 93 dB (A); guaranteed L

WA

 = 96 dB (A)

P = 0,55 KW; L/Ø =  cm

Notifi ed Body: TÜV SÜD Product Service GmbH (0036)

 

Ridlerstraße 65, 90339 München

 2012/46/EU

Emission No.:

Standard references:  EN 60204-1; EN 12151; EN 62321; 

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 06.07.2016

First CE: 16  

 

Archive-File/Record:

 NAPR014361

Art.-No.:

 44.722.91 

I.-No.: 11016 

Documents registrar:

 R. Gehard

Subject to change without notice

 

Wiesenweg 22, D-94405 Landau/Isar

 ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Declaration of confirmity

Summary of Contents for CMX-125U











Reviews: