manualshive.com logo in svg

oxycom CABIN 400, Operating Manual

Share
Download
oxycom CABIN 400 Operating Manual Download Page 25

Technical specifications

25

00010605 B

25

6.3

Functional principles of the OXYCELL when 
cooling

This section goes into more detail than the section entitled 

"Function" on page 6

; it 

will be of interest to readers who wish to know more about the cooling principles 
used.

A fan in the roof unit sucks in air from the outside. The incoming air is separated into 
two air streams within the OXYCELL: one air stream, which only comes into contact 
with a permanently dry surface in the OXYCELL, and a second air stream which flows 
across a different surface in the OXYCELL that is moistened by a sprinkler.

The air stream over the damp surface absorbs moisture and is allowed to escape 
through the roof unit. This cools the OXYCELL, thereby also cooling the air stream 
across the permanently dry surface in the OXYCELL. This cool, dry air flows through 
the OXYZONE into the caravan / camper. 

Turbidity

1

FTE

Iron content

0.2

mg/l

Colony count at 22ºC

100

kve/ml

Table 3

Water quality required for the CABIN 400 

Parameter

Max. value

Unit

Note

Summary of Contents for CABIN 400































Reviews:

No comments

Brands by name

Popular brands

Load more brands