manualshive.com logo in svg

oxycom CABIN 400, Operating Manual

Share
Download
oxycom CABIN 400 Operating Manual Download Page 17

Application and use

17

00010605 B

17

3.13

The meaning of the LED indicators

Table 1

The meaning of the LED indicators on the OXYZONE's operator panel

LED signals

Meaning

The CABIN 400 is turned off.

Ventilation 

Fan setting (in this example: setting 3).

Cooling

Cooling system start-up.

Cooling setting (in this example: setting 4).

Water reservoir 

Insufficient water in the water reservoir.

See 

"Refilling the reservoir (systems without automatic 

replenishment)" on page 14

.

Drain and refill the water reservoir.
See 

"Draining the water reservoir" on page 14

.

(Only applies if the water reservoir is automatically replenished 
from the fresh water tank).

The fresh water tank pump has been in operation for longer 
than is needed to fill the water reservoir.

1.

Fill the fresh water tank.

2. Reset the system by pressing 

.

Note: After approx. 3 minutes the system will turn off the 
pump in the fresh water tank; this pump can overheat or run 
dry when operated continuously.

Storage mode 

Storage mode process activated.

See 

"Storage mode" on page 22

.

Storage mode process completed.

See 

"Storage mode" on page 22

Summary of Contents for CABIN 400































Reviews:

No comments

Brands by name

Popular brands

Load more brands