Owon HDS200 Series User Manual Download Page 25

Page: 25 / 44

Function

Menu

Setting

Description

Luminance 10% - 100%

Set the screen backlight to increase in a 10%
cycle.

Backlight

time

30s
60s

120s

Unlimited

Set the screen backlight luminance time.
Unlimited means always on.

Menu time

10s
20s
30s
60s

Set the menu display time.

Elapsed

runtime

00h

：

00m

Display how long it has been powered on.

⚫

System

The description of the menu is as follows:

Function

Menu

Setting

Description

Language

Simplified

Chinese

English

Set the menu language.

Shutdown
time

10 minutes
30 minutes
60 minutes

Unlimited

Set the automatic shutdown time. Unlimited
means no shutdown. Please pay attention to this
setting if you use the battery only.

Buzzer

On
Off

Buzzer switch. The buzzer is turned on by
default in the multimeter mode.

1/2

Enter the next menu

About

After pressing this key, the instrument model,
serial number, version, and checksum can be
displayed.

System
upgrade

To upgrade the system. The version of the
upgrade package must be higher than the
version of the instrument itself.

2/2

Return to the previous menu

⚫

Default Settings

Press the

System

key to enter the system setting menu. Select

"Default

Setting", the screen will prompt "press < F3 > to execute the default setting,

Summary of Contents for HDS200 Series













































Search results

Summary of Contents for HDS200 Series

Reviews:

Related manuals for HDS200 Series

Brands by name

Popular brands

Owon HDS200 Series, User Manual

Search results

Summary of Contents for HDS200 Series

Reviews:

Related manuals for HDS200 Series

Brands by name

Popular brands