background image

STEP 7

Complete the Programming:

1.  Restore power to the garage door opener.

2.  Follow the on screen prompts to complete the set-up  and test the OHD Anywhere™ system.

NOTE:

 

This kit includes one DPS sensor for use with one door only. Additional DPS sensors can be purchased separately from your local Overhead 

Door Distributor.

NOTE:

 

A white light will flash and an audible beep will sound as an indication that the door is about to move when commanded by the OHD 

Anywhere™  or other compatible app(s).

Use of this product, the software embedded within this product and the related application software is subject to the Terms and Conditions 

available at: www.OverheadDoor.com/OHDAnywhere.

Features:

If the garage door opener is 

operated by any means, the 

OHD Anywhere™ app will 

send an alert to your device 

indicating the status of the 

garage door.

A log is also created to indicate 

when the door was operated 

and by what means. 

Visit www.OverheadDoor.

com/OHDAnywhere for more 

information.

DO NOT RETURN 

PRODUCT TO STORE.

For technical assistance, 

contact OHD Anywhere™ 

Customer Service at 

1-888-901-2750.

STOP

Summary of Contents for ohd anywhere












Reviews: