background image

ClimaCon F 

Safety-related information

2.  Safety-related information

2.1  Correct use

Operational safety is only guaranteed if the product is 

used as intended. 
The ClimaCon F room thermostats are electronically 

controlled operating devices for controlling surface 

heating and cooling systems as well as heating and 

cooling ceilings in detached houses or multiple dwellings.
Any use beyond and/or different from this is unintended 

use. 
Claims of any kind against the manufacturer and/or his 

authorised representatives for damage resulting from 

unintended use cannot be recognised.
Intended use also includes correct compliance with these 

instructions.

2.2  Warnings

Each warning contains the following elements:

Warning symbol 

 SIGNAL WORD

Type and source of danger!

Possible consequences if the danger occurs or the 

warning is ignored.

 

!

Ways to avoid the danger.

Signal words define the severity of the danger posed by a 

situation.

WARNING

Indicates a possible danger with moderate risk. If the 

situation is not avoided, death or serious bodily injuries 

may result.

CAUTION

Indicates a possible danger with lower risk. If the 

situation is not avoided, minor and reversible bodily 

injuries will result.

NOTICE

Indicates a situation that can potentially result in damage 

to property if not avoided.

2.3  Safety instructions

We have developed this product in accordance with 

current safety requirements. 
Observe the following instructions for safe use.

2.3.1  Danger

 due to electric current

 

!

Make sure that the product can be disconnected 

from the power supply at any time.

 

!

(

ClimaCon 230 V only

) The power supply you use 

must meet the criteria of overvoltage categories 

I or II according to DIN EN 60664-1. At the 

installation site, observe any additional applicable 

legal requirements derived from the IEC 60364 or 

HD 60364.

 

!

Do not operate the product if there is visible 

damage.

 

!

Work on the power supply may only be carried 

out by a specialist electrician.

 

!

Disconnect the product from the power supply 

at all poles for installation work, secure it against 

being switched on again and check that no 

voltage is present.

 

!

Only install the product in dry indoor areas.

 

!

For devices with a 24 V power supply, use a SELV 

voltage source that is galvanically isolated from 

the earth potential.

 

!

The setback input (ClimaCon F 90,  F 100; 

terminal 4) and the change-over input (ClimaCon 

F 100, F 310; terminal 5) are not potential-

free. Avoid direct contact. Do not connect any 

equipment here that could be damaged by 

electrical potentials or whose function could be 

disturbed. 

2.3.2  Danger due to insufficient personnel 

qualification

Work on this product may only be carried out by suitably 

qualified specialist tradespeople.
Due to their professional training and experience as well 

as knowledge of the relevant legal regulations, qualified 

specialist tradespeople are able to carry out work on the 

described product in a professional manner.

Operator

The operator must be instructed in the operation by 

specialist tradespeople.

2.3.3  Availability of the operating instructions

Every person who works with this product must have read 

and apply this manual and all applicable instructions.
The instructions must be available at the place of use of 

the product.

 

!

Pass on these instructions and all applicable 

instructions to the operator.

6

115500984-V07.11.2022

Summary of Contents for ClimaCon F

























Reviews: