Outdoor living today 9x6 Cabana Assembly Manual Download | Manualshive

Page: 1 / 26

background image

9x6 Cabana

Assembly Manual

Thank you for purchasing
a 9x6 Cabana. Please take
the time to identify all the
parts prior to assembly.

Note, The General Assembly
Manual illustrates a Door
Configuration in the front
center location. The Door can
also be positioned in the front
corners. To correctly configure
Door in front corners, follow
general assembly steps and
refer to Page 25 for required
changes.

Safety Points and Other Considerations
Our products are built for use based on
proper installation and normal residential
use, on level ground. Please follow the
instruction manual when building your
shed and retain the manual for future
maintenance purposes.

Some of the safety and usage measures you may wish to consider include:

-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the
snow off the roof(s).
-if the product is elevated, any structural and building code requirements are solely the customer's
responsibility, and should be abided by.
-in high or gusty wind conditions it is advisable to keep the structure securely grounded.
-have a regular maintenance plan to ensure screws, doors, windows and parts are tight.

Customer agrees to hold Outdoor Living Today Partnership and any Authorized Dealers free
of any liability for improper installation, maintenance and repair.

Version #3
May 2007

1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 1

1
2
3
...
»

Summary of Contents for 9x6 Cabana



























Reviews:

No comments

Related manuals for 9x6 Cabana

Brand: Palmako Pages: 25

Brand: Palmako Pages: 32

SunShed Garden Shed SSGS1212-AK-METAL

Brand: OLT Pages: 45

Brand: Storite Pages: 8

Extension LA28-1624

Brand: Palmako Pages: 92

Brand: Palmako Pages: 113

Brand: Palmako Pages: 36

Brand: Lasita Maja Pages: 37

Brand: Sojag Pages: 52

Brand: Karibu Pages: 48

Brand: Mercia Garden Products Pages: 5

Brand: HOKLARTHERM Pages: 109

Brand: Bear County Pages: 16

Brand: Palmako Pages: 38

02DTTWR0605-V1-PEFC

Brand: Mercia Garden Products Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands