Outdoor living today 8x12 Gardener's Shed Assembly Manual Download Page 11 | Manualshive

Page: 11 / 30

background image

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 11

23.

Place Window Wall Panel in front. Make sure top Wall framing is aligned together as illustrated

and attach as per

Step 17.

24.

Position and attach Narrow Wall Panel to left side wall stud with 3 - 2 1/2” screws as per

Step 17.

Note,

Narrow Wall is 73” high (2” shorter than wide walls). Siding overhangs wall stud and floor.

25.

Locate Vertical Door Jamb and position flush against right wall panel stud. The Jamb is 3” wide and

will sit flush to outside of wall siding. When positioned correctly, secure Jamb using 4 - 2 1/2” screws.

Jamb sits flush with
outside of siding.

«
...
9
10
11
12
13
...
»

Summary of Contents for 8x12 Gardener's Shed































Reviews:

No comments

Related manuals for 8x12 Gardener's Shed

Brand: NEC Pages: 106

NBX V3000 Analog

Brand: 3Com Pages: 2

Brand: Gardena Pages: 3

Brand: X-METAL Pages: 36

Brand: IBM Pages: 80

Brand: QNAP Pages: 62

Brand: QNAP Pages: 130

Brand: QNect Pages: 2

Artu 23.8610.95

Brand: Kelu Pages: 12

Brand: FWB Pages: 22

Vision-EL ELV421661

Brand: MIIDEX LIGHTING Pages: 2

ST31000333AS - Barracuda 7200.11 1 TB SATA 32 MB Cache Bulk/OEM Hard Drive

Brand: Seagate Pages: 2

Brand: Oklahoma Sound Pages: 8

Brand: WE-EF Pages: 7

XCUBESAN XS5226S XCUBESAN XS3224D

Brand: Qsan Pages: 138

Brand: YARDART Pages: 2

Brand: WE-EF Pages: 9

Brand: Landmann Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands