background image

1212

12

6.

Install the steering output fittings.

Plastic caps placed on the open ends of the fittings 
will prevent excessive leakage prior to hose 
installation.

Locate the steering lines at the head and rod ends of 
the left steering cylinder at the center of the 
machine (Figure 6, top). Disconnect the machine’s 
steering hoses and install run-tees 

HO

. Reconnect 

the machine’s steering hoses to the open ‘T’ end of 
each run-tee (Figure 6, bottom).

7.

Install the steering output hoses.

a.

Connect steering hoses 

HV

 (the longer) and 

HW 

to 

the stem of the run-tees at the head and rod ends of 
the steering cylinder respectively (Figure 7a).

Route the hoses, with other plumbing and clear of 
moving parts back and up to the hydraulic steering 
block. Use ties 

HY

 as necessary.

b.

Connect the hoses 

HV 

and 

HW

 to adapter fittings 

HC

 in the 

and

 B

 ports of the hydraulic steering 

block (Figure 7b).

8.

Install the steering controller.

Using hardware 

HJ

, install steering controller 

HI

 

on its mounting bracket 

HH

. Mount

 HI

 with its 

connector sockets inward and the pressure wash 
warning on top (Figure 8).

9.

Verify operation.

During tests of the hydraulic system, the 
machine may move unexpectedly. Be 
prepared for machine movement to avoid 
injury. 

Keep others away and stay clear of 
mechanical steering linkages to prevent 
serious injury or death from pinch point 
hazards while manually operating the 
hydraulic steering circuit. 

a.

Tighten all connections and clean up the installation 
area around the machine and make certain that it is 
safe to operate.

b.

Start the machine and check hydraulic connections 
for any leaks.

c.

Rotate the steering wheel from one extreme to the 
other and back. 

Figure 6: Steering hoses (top), run-tees installed
and machine’s hoses reconnected (bottom)

Figure 7a: Steering hoses connected at steer-
ing cylinders

Figure 7b: Steering hoses connected to steer-
ing block

Figure 8: Steering controller attached to steer-
ing block

HO

Machine’s steering lines

HV

HW

HC

HV/HW

HH

HJ

HI

Summary of Contents for EDX-VD6





















Reviews: