6
0911
Paper jam
You have fed in too much paper.
• Set the slider switch to "REV".
Pa per is pus hed out.
• Se pa ra te pa per stack
• Set the slider switch to "ON" again.
• Feed in pa per successively.
Shredded material container full
NOTICE!
Check the level in the shredded material con-
tainer and empty it in good time, as otherwise
the function of the cutting device could be
impaired.
• Switch equipment off.
• Move cutting head away.
• Empty cut material container.
• Remove cutting head.
For all other malfunctions, check whether the cutting head was
correctly positioned on the shredded material container before
contacting our customer service. If the motor was overloaded,
let the shredder cool down for 30 minutes before using it again.
REV
OFF
ON/AUTO
REV
OFF
ON/AUTO
REV
OFF
ON/AUTO
6 Troubleshooting
EC declaration of conformity
Machinery directive 2006 / 42 / EC
EMC directive 2004 / 108 / EC
Low voltage directive 2006 / 95 / EEC
HSM GmbH + Co. KG
, Austrasse 1 - 9, D-88699 Frickingen
hereby declares that the document shredder
OTTO Of
fi
ce OX5
complies with the EC directives listed above, including all modi-
fi
cations that apply.
Applied standards and technical speci
fi
cations:
• EN 55014-1:2006
• EN 55014-2/ A1:2001
• EN 61000-3-2:2006
• EN 61000-3-3/A2:2005
• EN 60950-1:2006
Frickingen, 01.04.2009
Josef Käppeler - Technical Director
This explanation only refers to the state of the machine when it was
fi
rst
put into use. Subsequent modi
fi
cations are not taken into account.
Kä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
pp
p
p
p
p
pp
pp
pp
pp
p
p
pp
p
p
p
p
p
eler
r
r
r
r
r
r
r
r
r
r
r
r
-
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
echni
9 Technical Data
Cutting type
Cross cut
Shred size
1/8“ x 1 8/16“ (4 x 38 mm)
Sa fe ty ra ting DIN 32757 – 1
3
Cutting ca pa ci ty DIN A4, 80 g/m
2
5 sheets
Lo ading width
220 mm
Cutting speed
17.1 ft/min (87 mm/s)
Voltage
120 V / 60 Hz
220 - 240 V/50 - 60 Hz
Operating mode
Brief operation
Max. operating time
3 min
Dimensions W x D x H
12.9“ x 8.1“ x 15.4“
(328 x 207 x 391 mm)
Weight
7.3 lbs. (3.3 kg)
Volume of shredded material container 3.6 gal (16 l)
english
WARNING
Dangerous mains voltage!
Switch off the shredder and pull out the mains
plug.
When cleaning only use a soft cloth and a mild soap-water solu-
tion. However, no water must enter the equipment.
After approx. every 100 working cycles, spray standard, com-
mercially-available, special cleaning oil for shredders through
the feed opening over the entire width of the cutting device. Let
the cutting device run backwards several times in the „REV“
setting without feeding in any paper. This loosens paper dust
and particles.
7 Cleaning and maintenance
Warning!
Before switching the machine on, make sure that
you observe all safety instructions.
Switching the paper shredder on
• Set the sliding switch to „ON/AUTO".
The „READY“ display glows.
The shredder is now ready for operation.
Feed paper
• Feed in the paper to be shredded, however,
never feed in more than 5 sheets at a time
.
The cutting device starts automatically,
pulls in the paper and shreds it.
When the feed opening is clear of paper
again, the cutting device switches off.
Swit ching paper shredder off
• Set the sliding switch to "OFF".
REV
OFF
ON/AUTO
REV
OFF
ON/AUTO
5 Operation
Electronic devices must not be disposed of with the
household rubbish. Please ask your local authorities
for collection points for electronic waste where you
can deposit old devices for environmentally-respon-
sible treatment and recycling.
8 Disposal / Recycling
Summary of Contents for OX5
Page 15: ...0911 15...
