background image

All  components  of  the  product  must  be  disposed  of  properly  in  accordance  with  the  respective  national  environ­
mental regulations.

11.2 Information on re-use

CAUTION

Used seat padding

Functional and/or hygienic risks due to re-use

Replace the seat padding if the wheelchair is to be re-used.

The  product  is  generally  suitable  for  re-use.  However,  please  note  that  the  product  with  its  permanently  welded
dimensions was tailored to one individual.
Similar to second-hand machines or vehicles, products that are being re-used are subject to increased strain. Fea­
tures and functions must not change in a way that could endanger users or other persons during re-use.
The product must first be thoroughly cleaned and disinfected before it can be re-used. Then the product must be
examined by an authorised specialist to check the condition and to look for wear and possible damage. All worn
and damaged parts as well as components which do not fit or are unsuitable for the new user must be replaced. 
Detailed information on replacing components as well as information on the required tools and the prescribed ser­
vice intervals can be found in the service manual.

12 Legal information

All legal conditions are subject to the respective national laws of the country of use and may vary accordingly.

12.1 Liability

The manufacturer will only assume liability if the product is used in accordance with the descriptions and instruc­
tions provided in this document. The manufacturer will not assume liability for damage caused by disregarding the
information in this document, particularly due to improper use or unauthorised modification of the product.

12.2 Warranty

Further information on the warranty terms and conditions can be obtained from the qualified personnel that has fit­
ted this product or the manufacturer's service (see inside back cover for addresses).

12.3 Lifetime

Expected lifetime: 

4 years

The design, manufacturing and requirements for the intended use of the product are based on the expected life­
time. These also include the requirements for maintenance, ensuring effectiveness and the safety of the product.

13 Technical data

INFORMATION

All information in the following tables refers to the respective custom-made model. The dimensional tolerance is
+/-15 mm, +/-2°.

Dimensions

Frame length

Custom fabrication

Lower leg length [mm]

Custom fabrication

Minimum frame length [mm]

Custom fabrication

Minimum rear seat height [mm]

330

Maximum front/rear seat height [mm]

Custom fabrication

Width

1)

Overall  width  =  seat  width  +  20  mm  per  degree  of
wheel camber

Overall height

Custom size

Back height [mm]

from 220

Armrest height

Custom size

Length with footrest

Custom size

Length without footrest

Custom size

Seat cushion thickness [mm]

30; 50; 60; 90

35

Invader 480S26=20000_K

Legal information

Summary of Contents for 480S26 20000 K









































Reviews: