background image

9.5 Side panels

CAUTION

Pinching at the side panels

Pinching, crushing due to lack of caution in danger areas

Pay attention not to pinch parts of your body between the side panel or frame parts.

The side panels protect the user from  dirt and in case of a collision during  competitive sports. They also ensure
that the user is securely supported in the wheelchair.
Welded side panels with fixed sidewall (see fig. 31) or welded side panels with tensioning belts (see fig. 32) may
be  installed,  depending  on  the  order.  The  tensioning  belts  with  hook-and-loop  closures  can  be  adapted  to  the
requirements of the user.

31

32

9.6 Drive wheels

WARNING

Improper installation of removable wheels

Tipping, falling over of the user due to wheels coming off

After each assembly, verify the proper fit of the drive wheels.

The quick-release axles must be firmly locked in the wheel attachment device. 

The clamp axles have to be fully countersunk and the clamp brackets must be closed to the stop.

CAUTION

Defective tyres

Accidents/falling due to poor traction, reduced braking force or lack of manoeuvrability

Maintain sufficient tyre pressure. The correct tyre pressure is printed on the tyre sidewall.

Ensure that the pressure is the same in both tyres.

Ensure that the tyres have sufficient tread depth. 

CAUTION

Reaching into exposed drive parts

Crushing, pinching due to incorrect handling

Do not reach between the drive wheel and side panel when driving your wheelchair.

Do not reach into the spokes of the rotating drive wheel.

CAUTION

Heat development when braking with handrims

Burns due to insufficient hand protection

Wear wheelchair gloves when travelling at high speeds.

The wheelchair is moved, steered, braked and stopped with the help of the handrims on the drive wheels.
To make transport easier, drive wheels with quick-release axle can be taken off the wheelchair.

23

Invader 480S26=20000_K

Use

Summary of Contents for 480S26 20000 K









































Reviews: