ENGLISH
1 - Description of the unit
The GENIUS range of display units are built in modules with a useful internal length of 622 mm (MODEL 70), 937 mm
(MODEL 100), 1250 mm (MODEL 135) and 1875 mm (MODEL 200) and can be in two different heights: 1250 mm (H125) or
1450 mm (H145). All these cabinets are multiplexable and are equipped with an integral condensing unit, with fan assisted
refrigeration. FIG. 1 on page 1 clearly shows the general look and dimensions of these units.
2 - Handling the unit
The unit comes with wooden slides (wooden crating available on request) to allow handling by a forklift truck. Only
authorised technicians should handle the unit.
FIG. 2 on page 1 shows the weight of the units in the different lengths and relevant lifting points.
3 - Receipt and storage
On delivery, check that the unit has not been damaged during transport. Check the condition of the packaging: if the
packaging is damaged, check the contents in the presence of the carrier.
For storage, make sure that the unit is protected against the weather and stored at a temperature between -25°C and +55°C;
30-95% relative humidity.
Take special care when unpacking the unit, as the packaging contains various parts and/or accessories needed to complete
the display unit (spacers, front risers, etc).
Remove the brackets and the pallet (see FIG. 4 on page 2) and then remove the transparent protection around the unit.
Place the display unit exactly where you want to install it. Move the unit properly: never drag by its sides!
Warning:
Inform the Manufacturer immediately if the unit arrives damaged. Any delay in doing so relieves the Manufacturer
of all liability.
Oscartielle cannot be held liable for any damage caused to the unit by mishandling and inaccurate storage.
4 - Installation and environmental conditions
The unit must sit on a perfectly levelled floor. When fully loaded, the display unit should not vibrate (see FIG. 5 on page 2).
The efficiency of the unit may be compromised if this is not perfectly level!
The display unit must never be placed in areas where explosive gas substances are used.
The unit should not be left outdoors or exposed to the rain (see FIG. 3 on page 2).
The stated performance of the unit refers to the climatic class (according to international standards ISO 1992/II/1973) which
foresee an ambient temperature of 25°C with 60% relative humidity in standard climates (3 EN 441) and 30°C with 55%
relative humidity in tropical areas (4 EN 441).
Sufficient space must be provided to guarantee good air circulation for the condenser (see FIG. 11 on page 3). Do not place
objects in front of the condenser protection grid, as this could compromise the efficiency of the refrigerated display unit (see
FIG. 6 on page 2). The performance will be less than expected if the environmental conditions differ from those foreseen, or
the display units are exposed to air flows of more than 0.2m/sec or heat radiation.
To avoid this problem, the User should send the Manufacturer details of the environmental conditions before finalising the
design of the units, so that the technical parameters and material options can be modified and the installer be informed of the
refrigerating power actually required.
5 - Electrical connections
The display unit must be connected to the power supply by fitting the power plug in a power socket. The display unit is not
provided with a circuit-closing switch and so a remote-control switch should be fitted upstream from the power socket. For
this operation advice should be sought from an electrician.
Warning:
Before connecting the unit to the mains, make sure that the mains voltage corresponds to that indicated on the
serial plate (bearing in mind that the max acceptable variations in voltage are +/-6%). Check that the cable used has the right
cross-section and length to withstand the current and the power absorbed by the combination, as indicated in TAB.1 on page
3 (climatic class 3 = 25°C RH60%; climatic class 4 = 30°C, RH55%). The "plug-in" units are supplied already fitted with a 2,5
m. cable and plug (see FIG. 7 on page 2) and so the unit must not be installed more than 2,5 m. from the nearest wall
socket. The display unit must be connected to its own fixed current socket (i.e. without extension leads or multiple plugs).
The cable should be fully extended and located where it is unlikely to hit, caught or trod upon, away from water and other
liquids and heat sources and must not be damaged (if damaged, get it replaced by an expert electrician, in compliance with
local regulations). The plug must still be accessible even after installing the unit.
Warning:
Follow the Manufacturer's instructions to install the unit, using qualified personnel and in compliance with the
electrical regulations for the specific country (electrical safety standards and laws, accident and fire prevention laws, EC
directives). Incorrect installation may cause injury and damage; the Manufacturer cannot be held liable for this.
The unit must be earthed. The Manufacturer cannot be held liable for any damage or injury should this safety regulation be
ignored. If the unit is to be installed far from the electrical sockets, suitable electrical connections are needed and these must
comply with the prevailing standards. The use of adapter plugs is strictly prohibited.
The Manufacturer cannot be held
liable for any damage or injury arising from incorrect installation.
16
Summary of Contents for GENIUS H125
Page 47: ......
