background image

 

 

14

 

 

ORTNER GmbH | Hürmer Straße 36 in A-3382 Loosdorf | Tel +43 2754 2707 | Fax +43 2754 2708  

[email protected] | www.ortner-cc.at 

 

Fire and heat protection 

General: 

 
Mounted surfaces made of or  containing combustible materials (components to be protected) must be insulated  or 
shielded, so no temperatures can occur on these that exceed values greater than 85 °C. The same applies to built-in 
furniture. The building requirements of the respective state building regulations and state ordinances (e.g. fire code 
ordinance, guideline of the Austrian institute of construction engineering 

“OIB”, …) must be adhered to.

 

 
In the event that ELECTRICAL INSTALLATIONS and/or ELECTRICAL COMPONENTS are present in/on the mounting wall, 
then the fire protection must be implemented as follows:  

 

Electrical  installations  and/or  electrical  components  on  the  side  facing  the  stove 

  Construction  of  the 

insulation just as the mounting surfaces TO BE PROTECTED.  

 

Electrical installations and/or electrical components on the rear of the mounting wall, wall thickness greater 
than  12.5 cm  and  mounting  wall  detached  at  the  rear 

  Construction  of  the  installation  just  like  with 

mounting surfaces NOT TO BE PROTECTED.  

Mounting surfaces TO BE PROTECTED 

 
10 cm brick  10 cm insulation (in accordance with AGI Q132). 
In the event of the use of Ortner Isoboard: 10 cm brick  9 cm Ortner Isoboard. 
Or  3 cm  Isoboard  at  the  mounting  wall  +  active  back  ventilation  (at  least  5 cm  gap  width)  +  6 cm  Ortner  Isoboard 
(towards the stove, with offset joints). 

Mounting surfaces NOT TO BE PROTECTED 

 
8 cm insulation (in accordance with AGI Q132).  
In the event of the use of Ortner Isoboard: 6 cm Ortner Isoboard. 
 

 

Summary of Contents for SE11 56/56/42




















Reviews: