background image

WARNING

Fireplaces

MODEL

 

LEDFP-

50 | LEDFP-60 | LEDFP-72

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.

 

Electrical products can cause 

death or injury, or damage to property.

 

If in any doubt about the installation or

 

use of this product, consult a competent electrician.

WARNING — THE INSTALLATION MUST BE CARRIED OUT BY

 

A QUALIFIED

 

ELECTRICIAN. 

1.

DO NOT open any panels

2.

NEVER immerse in water or spray with water

3.

Turn OFF the appliance completely and let cool before servicing

4.

Only a qualified service person should service and repair this electric fireplace 

Instruction Manual

1-888-543-6473
1-888-541-6474

13376 Comber Way 

Surrey BC V3W 5V9

[email protected] 
www.ortechindustries.com

375 Admiral Blvd

 

Missis

s

auga

ON L5T 2N1

A p p l i c a t i o n   N o t i c e

NEVER leave this fireplace unattended

Connect to properly grounded outlets only

ALWAYS unplug the fireplace when not in use

This fireplace is hot when in use. To avoid burns, DO NOT let bare skin touch hot 

surfaces. If provided, use handles when moving this fireplace

Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, 

and curtains at least 3ft (0.9m) away from the front of the fireplace, and keep 

away from the sides and rear

Extreme caution is necessary when any fireplace is used by or near children or 

invalids and whenever the fireplace is left operating and unattended

DO NOT operate any fireplace with a damaged cord or plug or after the fireplace 

malfunctions, has been dropped or damaged in any manner. Discard the 

fireplace, or return to authorized service facility for examination and/or repair

DO NOT run power cord under carpeting. DO NOT cover power cord with throw 

rugs, runners, or similar coverings. DO NOT route power cord under furniture or 

appliances. Arrange power cord where it will not be tripped over

DO NOT insert or allow foreign objects to enter any ventilation or exhaust 

openings, as this may cause electric shock or fire, or damage to the fireplace

To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. 

Doing so could cause a fire. DO NOT use on soft surface, like a bed, where 

openings may become blocked

This fireplace is not intended to be a primary heat source. It is for supplemental 

heat only. INDOOR use only — NEVER use this fireplace outdoors

ALWAYS disconnect this unit from the power supply before performing any 

assembly or cleaning, or before relocating the electric fireplace

ALWAYS check your fireplace cord and plug connections with each use:

1) Make sure the plug fits tight in the outlet. Faulty wall outlet connections or 

i)

loose plugs can cause the outlet to overheat

2) Fireplaces draw more current than small appliances. Overheating may occur 

2) 

even if it has not occurred with the use of other appliances

3) If the outlet or face plate is hot, discontinue use immediately and have a 

3)

 qualified electrician inspect and/or replace the faulty outlets

Check the parts list to make sure nothing is missing. Dispose of packaging 

materials properly. Please recycle whenever possible

Tools required (not included) are: Phillips screwdriver, stud finder, level; tape 

measure, electric drill; 1/4" wood drill bit, and a hammer

 

D

O NOT

AUTION

CAUTION

A fireplace has hot and arcing or sparking parts inside. DO NOT use it in 

areas where gasoline, paint, or flammable liquids are used or stored

Use this fireplace only as described in this manual. 

Any other use not recommended by the manufacturer may cause fire, 

electric shock, or injury to persons

ALWAYS plug heaters directly into a wall outlet/receptacle. 

NEVER use with an extension cord or relocatable power tap 

(outlet / power strip)

DO NOT place the fireplace near a bed because objects such as pillows or 

blankets can fall off the bed and be ignited by the fireplace

NEVER use this fireplace in bathrooms, laundry rooms, or any other 

location where the fireplace could fall into a bathtub or pool, become 

damp, or come in contact with water

Avoid fire — regularly inspect all air vents to make sure they are free 

from dust, lint or other blockage. Unplug the unit and clean with a 

vacuum only. DO NOT  rinse or get it wet

ALWAYS mount to wall bracket before use. DO NOT set on the floor, or 

other surface, to use. NEVER use a wall mount bracket from another 

manufacturer

Risk of electric shock — DO NOT open. No user-serviceable parts inside

ALWAYS turn the fireplace off before unplugging it from the outlet

ALWAYS store this fireplace in a dry location. NEVER use this fireplace if it 

has become wet. NEVER plug this fireplace into an outlet that is old, 

cracked, or has any loose wires or connections. Plugging this fireplace 

into a faulty outlet could result in electric arcing within the outlet that 

could cause the outlet to overheat or catch fire

The power cord supplied with the fireplace has three prongs: 

two flat blades (LIVE and NEUTRAL) and one round pin (GROUND). If a 

3-

slot receptacle is not available, an adapter MUST be used. The adapter 

MUST be PROPERLY GROUNDED to the outlet box (see Fig. A).

Adapter is not included.

This product includes a GLASS panel. Always use extreme caution when 

handling glass. 

F

ailure to do so could result in personal injury or property 

damage. Remove all parts and hardware from the carton and place them 

on a clean soft dry surface. Parts and assembly steps are grouped for 

wall-hanging or recessing use. 

 

D

O NOT

PARTS & HARDWARE

Fireplace

Wood Screw

Wood Screw

Drywall anchors

Remote Control

Remote Control

Drywall anchors

Wall bracket

Decorative pebbles

Decorative crystals

Log set

Plastic tray

Summary of Contents for LEDFP-50








Reviews: