background image

Instruction Manual

1-888-543-6473
1-888-541-6474

13376 Comber Way 

Surrey BC V3W 5V9

[email protected] 
www.ortechindustries.com

375 Admiral Blvd

 

Missis

s

auga

ON L5T 2N1

CONTROL PANEL / TOUCH PANEL / REMOTE CONTROL OPERATION

Fireplaces

MODEL

 

LEDFP-

5

0

 | LEDFP-60 | LEDFP-72

When the heater is first

 turned on,

a slight odor may be present. This
is normal and should not occur
again unless the heater is not used
for a long period of time

To improve operation, aim the
remote control at the front of the
fireplace. DO NOT press the
buttons too quickly. Give the unit
time to respond to each command

NEVER dispose of batteries in fire.
Failure to observe this precaution
may result in an explosion. Dispose
of batteries at your local hazardous
material processing centre

Important Reminder:

Small remote control uses one
CR2025 battery (included)

Big remote control uses two AAA
batteries (not included)

Remote control battery used
depends on the remote control
type which selected above

Remote Control Battery

Information:

Temperature Limiting Control

This fireplace is equipped with a temperature 
limiting control. Should the fireplace reach an unsafe 
temperature, the fireplace will automatically turn 
OFF. To reset:

1.

Unplug the power cord from the outlet

2.

Turn the ON/OFF switch on the control panel to
OFF. Wait 5 mins

3.

Inspect the fireplace to make sure no vents are
blocked, or clogged with dust or lint. If they are,
use a vacuum to clean the vent areas

4.

With the power switch in the OFF position, plug
the power cord back into the outlet

5.

If the problem continues, have your outlet and
wiring inspected by a professional

Cleaning

Metal:

Buff using a soft cloth, slightly dampened with a citrus oil-based product

DO NOT use brass polish or household cleaners as these products will damage the metal trim

Always turn the fireplace OFF and unplug the power cord from the outlet before 
cleaning, performing maintenance, or moving this fireplace. Failure to do so could 
result in electric shock, fire, or personal injury.

NEVER immerse in water or spray with water. 
Doing so could result in electric shock, fire, or personal injury.

Glass:

Use a good quality glass cleaner sprayed onto the cloth or towel. 
Dry thoroughly with a paper towel or lint-free cloth

NEVER use abrasive cleaners, liquid sprays, or any cleaner that could scratch the surface

Vents:

Use a vacuum or duster to remove dust and dirt from the fireplace and vent areas

Plastic:

Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water

NEVER use abrasive cleaners, liquid sprays, or any cleaner that could scratch the surface

Summary of Contents for LEDFP-50








Reviews: